Jump to content

Ronda 5022.D

Yani365
 Share

Recommended Posts

Yani365 New Member

Yani365

Posted
Posted

Hey folks! I have a project watch coming which uses a Ronda 5022.D movement according to the top plate on the movement.

Unfortunately, I can't find any information on this movement. It looks very similar to the 5021, but even the Ronda website doesn't have a technical sheet on this specific movement. In fact, they don't list a 5022 at all. 

Are there any other sources for the technical sheet for this? Has anyone worked on these before? 

Thanks in advance for any help! 

Y

Link to comment
Share on other sites
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Waggy
      Pivot Gauge

      By Waggy · Posted

      Learned a new thing today! 🤓 Looked this up and found this informative document: Watkins-MainspringGauges.pdf
    • Neverenoughwatches
      Cleaning solution clarification

      By Neverenoughwatches · Posted

      Correct one dip is expensive when the chemical is purchased as " one dip " which is why it is mostly reserved for these two small parts as far as information tells us it is mostly tetrachloroethylene. I use it bought as perchloroethyl used in dry cleaning processes, i cant say I'm overimpressed with it though it appears to me to be shellac safe. What may be a better solution for hairsprings is a high lab grade of pure benzine.  IPA is mostly used as a rinse and water displacer and yes it does have the potential to dissolve shellac, personally i would not buy anything that has significant water dilution so 99.9% IPA is the way to go. And lastly the part you are cleaning dictates your choice of cleaning brush, delicate parts like a hairspring requires the finest artist's brush you can find. Plates and bridges can take a little more scrubbing, but always check to make sure the surface is being unharmed. And dont forget a stick of tip benzine soaked correctly shaped pegwood is your mate set up for cleaning dirty jewels and removing stubborn dried up lubrication. 
    • RichardHarris123
      Hello from Indiana!

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Neverenoughwatches
      Pivot Gauge

      By Neverenoughwatches · Posted

      Den / Dennison is a unit measurement of size this is actually a mainspring gauge . I haven't heard of a pivot been measured in Dennison before.  Though the small thickness gauge is  usually supplied with a Jacot tool and is more accurately known as a pivot destroyer.
    • Waggy
      Pivot Gauge

      By Waggy · Posted

      Could it be an abbreviation for Denier? "Denier (/ˈdɛniər/) or den (abbreviated D), a unit of measure for the linear mass density of fibers, is the mass in grams per 9,000 metres of the fiber. The denier is based on a natural reference: a single strand of silk is approximately one denier; a 9,000-metre strand of silk weighs about one gram." The pivot gauge looks interesting, however I wouldn't trust myself to drive a pivot into a wedge incase it jams and gets damaged/snaps trying to get it free. More a comment on my ability and incompetence than the quality or design of the tool 🤣
×
×
  • Create New...