Jump to content

Hello, All! ...New Member / First post...

ZebraMidge

By ZebraMidge
in Introduce Yourself Here

 Share

Recommended Posts

ZebraMidge Member

ZebraMidge

Posted
Posted

Me?  I'm a holdover from the manual and electro-mechanical typewriter industry. I have carried a tool kit all my life to the point that my tool kit arm is longer than the other!  LOL!

I'm old, but still curious as a cat and might finally be getting serious with my Horology education-have tinkered with watches for years, but nothing serious.  -opened my first watch case back in the 1960's and watched parts go a-flyin' !  Luckily, it was my brother's watch, so I wasn't out anything! :)

Recently I have been trying to regulate a Sellita SW200 that was gaining 2 minutes per day.  With help from a large magnet the watch is now at minus 15 seconds per day. Hoping to learn enough to take care of the problem,  Currently in process of buying proper tools,  I have a low dollar kit, but it is just not good enough (in my opinion). I'm a stickler for correct sized screwdrivers and despise a marred screw head!  My goal with screws are to keep them looking un-touched!

Best!

Zeb

Link to comment
Share on other sites
Endeavor Distinguished Member

Endeavor

Posted
Posted

Many here do have, or started off with a reasonable low dollar kit and if you get your fingers to do what you want them to do, you can get fairly far with them ! Once you get better, you most likely like / want to have some better tools. Whether these watch-tools ever going to be heavy enough to bring your other arm just as long as your tool-kit arm, that needs to be seen :D

Just like Geo; curious what you get up to ......

  • Like 1
Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Welcome Zeb I like you came through the same ranks, Imperial Remingtom  and Underwood to name but a few, Got hooked on watches and clocks a long time ago I too an "Old" but still love the clocks and watches got a house full. This is the place for help for sure some learned guys on here. 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      My first Gruens. Precision 510 and N510R movements.

      By rjenkinsgb · Posted

      Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...