Jump to content

Help with assembly seiko 6145-8000

Muligans
 Share

Recommended Posts

oldhippy Distinguished Member

oldhippy

Posted
Posted

I have said this many times on the forum. Ronsonol lighter fluid is shellac friendly. You could leave any watch part that has shellac on it in ronsonol for days. Just remember it evaporates very quick, so you need a pot with a screw lid.

It is always good practice in whatever cleaning fluid and rinse you chose to read the instructions and see if it is suitable for your needs. In my time, I used L& R cleaner and rinse and found them to be excellent. They were shellac friendly then. Today they might have changed the formula, so be careful.  

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

I would design the pallets/fork with slots for the pallets to slide in the fork and stay put. Or ,if the pallets adgustments are left for the assembly line, I would design fixture to hold the pallets in the right position to get shellac- ed. I certainly wouldn,t  count on shellac friendship.And about the heat, I warn you not to stand under the sun light or risk getting de-shellaced.

OH is right again, you just can,t be sure of the qualities,  be it oil, grease etc.

One might as well  get some grease off of this guy :bbq:.

The moments you spend laughing are happyy.

Regards joe

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is. I've attached a lesson regarding mainsprings, focussing on the size and strength of the spring within the barrel, you might find helpful. Unfortunately it is a PDF converted from a PowerPoint presentation, but only a slide was lost that was originally a video of fitting a mainspring   Lesson 5 The mainspring.pdf
×
×
  • Create New...