Jump to content

Hello all old (hour/minute/second)hands - this is me the new(est) guy!


wilding

Recommended Posts

Hello to all of you out there!

So, the moderator asked me to do some intros to myself. Here they are.

I'm just getting properly into watch repairs and slowly building my kit and various bags of to-be-fixed watches.

So far, I'm sticking to quartz watches. Actually I have a few books on repairing mechanical watches, but it is scary stuff! Maybe I just need to explore more.

I'm certainly NOT a pro, but a home-repairing amateur.

I have fixed quite a few already, but also killed some watches in the process. Hey, that's part of learning - right?

So, I guess that's all for now.

  • Like 1
Link to comment
Share on other sites

Hi Wilding, You are doing OK but you must get experience of mechanical watches. Learn how they work, Going barrel, mainspring, centre wheel, 3rd and 4th wheels, escape wheel. Lever, balance, canon and dial train, setting mech: etc. Practice on old cheap movements at first with mechanical sympathy and never force anything, gravity should do the job. Then gain experience and get confident. Of course read your books. All good wishes, Mike. PS. I am not a watchmaker, just a retired watch jobber but there is in depth help on this fine forum.

Link to comment
Share on other sites

  • 10 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
    • I have a PDF below that will help. The problem was the PDF wasn't designed for this purpose it was designed to tell you what size watch you  have. Then it doesn't take into account movements come conceivably in different thicknesses.   watch-ligne-size-chart.pdf
    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
×
×
  • Create New...