Jump to content

Seiko 5m43-0a40


Fire3

Recommended Posts

Hi all

 

i have a Seiko 5M43-0A40 kenetic watch that had a suspected faulty capacitor, I took it to my local watch repair man who has advised me their is a fault with the movement due to a previous repair (I can’t for the life of me remember where I took it to get repaired previously)

 

The watch has a lot of sentimental value to me, what are my options for replacing the whole movement? 

 

Thanks in advance 

Fire3

Link to comment
Share on other sites

So, did the watch repairman say exactly what was wrong with the movement? as it is hard to advise you if we don't know what the problem is.

My opinion would be to take it to someone who will tell you what the fault is and how much to repair, otherwise you are making decisions based on lack of information. Knowing this will help you decide if it is certain parts that need replacing or the whole movement.

Link to comment
Share on other sites

The movement 5M43 is obsolete, but most parts are still available, so it depends on what is wrong with it as to your best option.

Repair the existing movement, or find a donor movement from a second hand watch, Jon says we need to what is wrong before we can give advice.

Link to comment
Share on other sites

Thanks for the replies, I’ve contacted the repair man, he says the coils were damaged when the previous capacitor was changed and they used a cheap replacement capacitor which has leaked.

 

I’ve found a Hattori YT63 movement that I have been told is a direct replacement is this correct? 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I still need to see the complete movement as there are many types of Elgin movements. The part that you are holding is called a snail. 
    • Just a quick update on my T17. I just finished the service and, boy, was this nerve-wrecking.... I bent the hairspring a few times. Stupid accidents. Once it was beyond repair and I had to get a donor movement. The replacement hairspring turned out to be a few millimeters shorter and therefore the watch was running 6min too fast even when the regulator was set to the slowest position. So I needed to get timing washers (see another post here: https://www.watchrepairtalk.com/topic/25505-30t2-adjustment-of-timing-washers/?do=findComment&comment=248100).  After all, I'm now, getting a 310° amplitude (fully wound, dial up, lift angle 54°). About 250 in vertical positions. Quite a drop, but apparently not too abnormal for a 90-year-old watch with a slow beat rate (18000bph) and rather heavy balance wheel. After 24h I still get 280 (horizontal) and 220 (vertical). And now the highlight:  66h of power reserve! You may remember that I posted that I used a slightly weaker, but also slightly longer mainspring than prescribed. See my comments above.  I used GR 3937 (instead of GR 3632). So I recommend this mainspring and ticker oils (9020 on escape wheel and HP1300 on the rest of the train).    
    • OK! I was able to get a nice set of timing washers from ebay! And they worked really well. I needed to slow down the movement by about 6min and I put four (=two pairs) of 3-minute washers (rated for the the size of the movement) and it did pretty much exactly that. On one pair of screws, there were already washers. So I added a second washer on those screws. Maybe not ideal, but it doesn't cause any problems. Poise is ok.. not perfect.. but I had so many issues with the watch that I decided to accept it. It's a 90-year-old watch. Delta is around 40 seconds.   
    • I think it is friction fit, there are tools to remove them, cheaper versions are available. You could try adapting some pliers, see my crap drawing.  The pushers are available in various sizes, you could measure once the tube is removed. 
    • The entry jewel's not as bad but seems still too much lock. I do epilame the escape wheel and pallet jewels, then run dry for about 15 minutes, then put 9415 in exit jewel very little at a time and check with backlight how the oil's distributed.  Another question is about capped escape wheels. Should I somehow wear the epilame off the pivots before installing the wheel? I normally let the escape wheel run dry for that said 15 minutes when there's no cap jewel.
×
×
  • Create New...