Jump to content

Making a Balance Staff

jdrichard
 Share

Recommended Posts

jdrichard Distinguished Member

jdrichard

Posted
Posted

Need to make a balance staff for a European picket watch. The old staff had both pivots broken off. First I disassembled the watch and removed the balance staff. Removing the roller table was the hardest part because it was a Three arm balance and my Magic Roller Remover would not work so I used the scissor type.6747fe43a99bd188eacf952d9fef8dac.jpge7e75d9c69e9a769a9ad6711e9c6b4a6.jpg1fa88274beaa1d13932d30eec2514bed.jpgc078f7e520c6a346dfadcaff67cec649.jpg30f532e8ae4870da44c7cbcaa0281ed8.jpg1e2a163391ea846c35b2b298187f5b07.jpg844d0cfbd16fab2a941d595c66400080.jpg

I then determined the widest diameter of the balance staff and found a 2.0 mm piece of Blued Steel. I cut off 1 inch and sized the collet, and inserted in into my Boley Leinen Lathe. I then started to cut the Balance and Hairspring side by first using the old staff as a guide and marking the piece of steel with my carbide graver.84d1245e54d14e9c32e366e831d56e88.jpga8d59714009b2c8e9837c7d0a23a9576.jpg

I started cutting down the first diameter where the balance fits and simply cut and measure until it was snug but still room to stake it in place. I then cut the hairspring diameter next and fix and cut repeatedly until it was snug. I used a special gauge to measure as I went along. Once the part fit was good I worked on the pivot with the graver until I got it down to around 0.2 mm and then used a stone to get it to around 0.14. The rest I plan to do on a Jacot tool.0674a45da0908e5666cce3fe60dacaea.jpg5f5da6c0d5a8c8836f329b4007570fd4.jpg974ed69f2161befa35058fb02420bf8f.jpg

I then flipped the part around with a different collet and started working the Roller Table side using the same technique. I Amos finished off the plate where both the rolled table on one side and the balance on the other side rest.7f9288040022be85fb24dd8435190d3d.jpg

Slight error in the description. I left the full part in and started working on the roller table side before cutting off the part and flipping it around...saves time.fef5e1e9bedb5099cc57df61d48dd29c.jpge35b6f93179d1155af32162d51002e0d.jpg69dcc763d9f12d137ec285e3e6e5a2d8.jpg73865aa95c3ce5477a81ab5860cefa62.jpgae5f5dd2ca1ac1eaceaf541f66d0e1c0.jpg

I worked on the other pivot as well and got it down to 0.14 with a graver and then a stone...on the Lathe. The final product looked great. I am waiting for a set of vintage pin gauges to get the pivot size exact. Will finish it off next week.bae231293c9eefa9bb05910589d5ce6d.jpg13be0555c60fc6945650f2f963450b71.jpg

 

 

Sent from my iPhone using Tapatalk Pro

  • Like 8
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted

More progress. As well, made a video on how to use Jewel Hole Gauges. So I staked the balance wheel onto the newly made balance staff, friction fit, and it fit really well. Very pleased . I then used the jewel hole gauges to determine the hole size and this the pivot size. Turned out to be 0.10. Now I need to burnish the pivots to that size, fit the part in the movement and once fit perfectly, I will add the rolled table and the hairspring.



c26c2fd09d942f352dc3ca471539cc6a.jpge9e49f4d49e75f1966a590b151902e4c.jpg



Sent from my iPhone using Tapatalk Pro
  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted

Also lined up the impulse jewel to the center of two arms and then drew the line straight from the jewel to the pallet fork pivot then placed the hairspring on the balance loosely to align with stud; while the impulse was perfectly centred with between the banking pins.


Sent from my iPhone using Tapatalk Pro

  • Like 2
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchweasol
      Blew it with a coil

      By watchweasol · Posted

      Hi. Breaks like this can br fixed with conductive paint like the paint used to repair a car  rear screen heater. I have used it successfully, you don’t need much and unlike solder there is no heat 6020A-1.pdf
    • JohnR725
      Blew it with a coil

      By JohnR725 · Posted

      the problem with vintage watches and yes quartz watches can be vintage is availability of parts will be a problem. I have a link below where we can cross reference the coil and  I was hoping for more. Another problem for vintage parts are everyone on the group gets used to ordering from online. Conceivably the physical material houses that still exist out there might have the part and you'd have to reach out to them and see if anyone has one. this is because they don't list every single part that they have online with the exception of cousins where everything they do is online work just doesn't exist but the other material houses can have stuff not listed. Otherwise just set up a search on eBay and sooner or later it will possibly show up if you're lucky.   http://cgi.julesborel.com/cgi-bin/matcgi2?ref=SEK_6020A  
    • watchweasol
      Self introduction

      By watchweasol · Posted

      Hi welcome to the forum.    Enjoy
    • JohnR725
      Pocket watch escape wh

      By JohnR725 · Posted

      the bestfit book refers to Revue as wittnauer and the fingerprint we have this.
    • Waggy
      Difference between AS 1686 and ST 1686

      By Waggy · Posted

      Maybe a little off-topic, but it still amazes me that most people (and myself before I got into this hobby) don't realise that the movement of their watch was (in most cases) not made by the name on the dial of the watch. This is especially true of many 'fashion' watches which use the cheapest of cheap movements ($4 each) which are completely out of proportion to the overall cost of the watch ($++100s). Usually the actual manufacturer is stamped somewhere inconspicuous on the movement, usually around the balance, and this is what you need to find so you can locate spare parts or servicing manuals etc. This is like buying a top of the line Rolls Royce Phantom and learning it has a BMW engine..... oh wait a minute, it does! (6.75-liter, 460-horsepower BMW V12 engine - reference)
×
×
  • Create New...