Jump to content

Anyone know the manufacturer if this movement


Recommended Posts

Hello,

New to the forum, I am just starting my first go with trying to repair a mechanical watch that got water in it and then stopped. 

However, the watch is an old watch 70s I think and doesn't have a clear manufacturer indicated. 

Wonder if anyone can help with what type of movement this is in case I need to order parts.

Thanks for any help anyone can offer

IMG_20180906_003930.jpg

Link to comment
Share on other sites

Hello Leelemon,

On this friendly forum before making a post for help or advice. We like new members to introduce themselves. Just say a little about what you do and about yourself.

We like that to go into the Introducing Yourself Here. This is the link.

https://www.watchrepairtalk.com/forum/23-introduce-yourself-here/

Link to comment
Share on other sites

It looks remarkably like an st 96. When I embarked on this hobby a few years ago I purchased of a well known auction site what I thought was genuine Tissots Titoni Oris etc only to find that someone in this big wide world has purchased hundreds of these movements, stamped one of the bridges with Tissot Oris or whatever and then got a group of schoolchildren to repaint the dials. That is not to say that the st 96 is not a reliable unit. Its just that I learnt the hard way. Not everything is what it seems. Sellers are reluctant to show the movement.

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • The stress is the force (on the spring) x distance. The maximum stress is at the bottom, and decreases up the arm. That's why they always break at the bottom. I used a round file, then something like 2000 grit to finish. I gave the rest of the arm a quick polish - no need for a perfect finish. Just make sure there are no 'notches' left from cutting/filing. The notches act like the perforations in your toilet paper 🤣
    • It's probably a cardinal rule for watch repair to never get distracted while at the bench. Yesterday, after finishing a tricky mainspring winding/barrel insertion (I didn't have a winder and arbor that fit very well) I mentally shifted down a gear once that hurdle was passed. There were other things going on in the room as I put the barrel and cover into the barrel closer and pressed to get that satisfying snap. But when I took it out I realized I never placed the arbor.  When opening a barrel, we are relying on the arbor to transfer a concentrically-distributed force right where it is needed at the internal center of the lid. However, when that isn't present it's difficult to apply pressure or get leverage considering the recessed position of the lid, the small holes in the barrel and the presence of the mainspring coils. It was a beat-up practice movement so I didn't take a lot of time to think it over and I pushed it out using a short right-angle dental probe placed in from the bottom, but that did leave a bit of a scratch and crease in the thin lid. I had also thought about pulling it using a course-threaded screw with a minor thread diameter smaller than the lid hole and a major diameter larger, but that may have done some damage as well.  Thinking about how this might have been handled had it been a more valuable movement, is there a method using watchmaking or other tools that should extract the lid with the least damage? 
    • 🤔 what happens if lubrication is placed directly on top of epilame ? Making a small groove so the lubrication doesn't spread across the component but what if when lubing a little overspills and sits on the epilame .
    • Why just the bottom mike ? Is it worth polishing the whole arm ?
    • The one thing I took time over was to round and polish the curves at the bottom of the jumper arm. The slightest mark (left over from cutting of filing) acts as a stress raiser, just where you don't need it. 
×
×
  • Create New...