Jump to content

Help, an Art Deco watch after 80 years in a drawer !!


Recommended Posts

Hello All;

Another new challenge ! I just bought this ladies Art Deco watch; NOS, never been worn and has been standing still for 80 years of so......

It's a cylinder escapement and the balance wheel looks rusty. I have no idea whether is runs, according to the eBay add; "it needs a service". I thought I would throw in a bid and managed to get it for £15 including postage. What are your initial thoughts, how to tackle this one ??

AD-1.thumb.jpg.511755ca9bbcd666e3ba26d46631471f.jpgAD-2.thumb.jpg.cf19b9bad9681145778f51eb3411e60e.jpgAD-3.thumb.jpg.6ce05fe982409c0351719258f51deaea.jpgAD-4.thumb.jpg.74d9f6548782317bef8aa1905b247fd4.jpgAD-5.thumb.jpg.c5791ee1cffedfd0b7340b0a5e7260c7.jpgAD-6.thumb.jpg.493aeb6652486bc12d168a0efc1cfc33.jpg

 

Link to comment
Share on other sites

Thank you both for your swift reply ;)

I was thinking of making a walk-through of this one; from start to finish ..... it would be nice to get it back in tip-top condition!

@Chopin; what may this "special substance" be? Fibre-brush is already in my tool-kit.

 

Link to comment
Share on other sites

You need to check the hairspring and cylinder both for rust. Check the cylinder for wear. You can clean up the balance wheel with a glass fibre pencil brush in Ronsonol lighter fluid make sure you brush the same way all the time, that way it will have a nice finish and won't look scratched.

Link to comment
Share on other sites

Thank you all for the great tips :thumbsu:  The watch will be send from Germany to Denmark, so I expect it will be with me by the end of next week. We have to see in which condition it is in and obviously, I will report back as soon as I know more.

The luminous on the hands is another thing to watch, that has probably gone very brittle. Just in case, any restore tips here...? (I do have good white/green luminous; can one do an "age-trick" with/to the powder?)

Edited by Endeavor
Link to comment
Share on other sites

16 hours ago, nickelsilver said:

Don't forget you can't remove the balance with power on the gear train.

@nickelsilver; yes thanks, I knew ...... however it is not until now that I "miss" the ratchet-wheel and the click ..... on the dial side? Hmmm ....... Interesting. Also, so far I couldn't find any information about WAP, most likely German ....... I'll ask the seller, see what he knows ....

Link to comment
Share on other sites

10 hours ago, Endeavor said:

Thank you all for the great tips :thumbsu:  The watch will be send from Germany to Denmark, so I expect it will be with me by the end of next week. We have to see in which condition it is in and obviously, I will report back as soon as I know more.

The luminous on the hands is another thing to watch, that has probably gone very brittle. Just in case, any restore tips here...? (I do have good white/green luminous; can one do an "age-trick" with/to the powder?)

If you are very careful you should be able to remove and replace the hands and dial without damaging the luminous paint. As you say the will both be very fragile. You can mix paint pigment with luminous paste to try and match the colour, but it rarely looks like these do now.

Hopefully you will find that the original oil, whilst dried out and possibly hard to remove will have protected the running surfaces.

Good luck, keep us posted!

S

Link to comment
Share on other sites

@StuartBaker104; Reading your luminous tip, I'll better stick to the "if you are very careful" part ! ;)

Will keep you posted ..... I think it's great fun to bring something this old & fragile back alive. It's not the highest quality movement, but for me this little gem deserves it. We'll see how far we get ......

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
    • Sounds like the story with my Rolex. Poor (expensive) job done by an official Rolex dealer with an "in-house" watchmaker, hence I learned watchrepair and did the servicing myself. Same story as I learned with the Omega 861, again poor job by an "in-house" watchmaker by an official Omega dealer. Once your watch goes through that back-door, you have no idea what is going to happening to it 🫣   Quite nice that they sent back the parts which had been replaced !
    • yes that's definitely not right at all. I have a picture one of my friends has a Omega coaxial there was having issues to lose asking me where he should send it. As that's a specialty watch I suggested the service center. When he got it back he sent me a picture so the replace the dial as you can see the hands the mainspring barrel and I think the price was really quite decent considering all the stuff they can replace. So I do know they do change the barrels but the other person I worked at the service center when I would ask questions and unfortunately I can't remember all the answers. I think a lot of the changing a parts is at the discretion of the watchmaker. Plus I don't know enough about the chronographs and whether that would be considered a vintage watch? I take some of the vintage watches may have been sent directly to Switzerland or another service center. Obviously with a watch like the one down below they probably have a infinite supply of parts is its relatively modern vintage stuff becomes more interesting even the watch companies don't have necessarily infinite supply of parts. But no matter what the watch shouldn't disintegrated six months that's definitely an issue.        
×
×
  • Create New...