Jump to content

Watch Repair Training

RickTick
 Share

Recommended Posts

RickTick New Member

RickTick

Posted
Posted

Hi Guys

On the basis that you don't know what you don't know and I have never believed that I will ever know everything, I have signed up for Marks three courses.

Following on from that I will look to do the BHI training's and qualifications. I see this as being a three year plan, or CPD as the modern term goes.

Looking forward to learning new stuff.

All the best.

Rick

PS. I am looking for a jewelling press kit.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Good for you. I'm sure you will be a great intrest to you. When I started, I took up an apprenticeship back in the early 70's, it was 5 years then another two as an improver. I was very lucky as the workshop was well equipped and everything was at hand. My master was also extremely good in all aspects of horology, which helped me to gain the experience I have today. You will never stop learning.  

  • Like 2
Link to comment
Share on other sites
  • 2 months later...
Plodgey New Member

Plodgey

Posted
Posted

Hi Rick,

I have just joined and was wondering how the training has been going?

I am a real new guy  and want to learn as much as possible.

and my plan is pretty much identical to yours, I have looked at BHI practical courses but was wondering if it was worth doing the courses here before hand.

Thanks :)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...