Jump to content

Things I learnt the hard way

dieale2
 Share

Recommended Posts

dieale2 Member

dieale2

Posted
Posted

I been at this for about a year and I learnt a lot of things the hard way. I don't see any thread about lessons learn the hard way so I'll start here.

  1. Tea leave holders are not good parts holders. The two halves don't clamp down hard enough and small parts will slip through.
  2. Hairsprings are hard.
  3. Mainsprings are fragile.
  4. Just because someone been in business for 40 years doesn't mean they can't mislead you about vintage watches. Do you homework and don't only take the seller's word.
  5. If you don't know what an expensive vintage watch supposed to look like, don't buy it. 
  6. You will not save money by buying a bunch of "cheap" watches.
  7. You can't (or shouldn't) oil a watch with a single oil and grease.
  8. Organizing a lot of parts is hard.
  • Like 2
  • Thanks 1
Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

LOL.

I'm with you on point 2 and a gree with you on point 4,5,6 and 7 too.

I've been far too many clocks and watches butchered by so called professional watch and clock repairers.

The best one just last week which had been at a high street shop andamongst all the otehr things wrong with it they tried to put it in poise by soldering lumps of copper to the bimetallic balance.......

  • Like 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

You said it. Well almost.

May I add section 9 and..

Don,t lean over work bench or the piece. Instead hold your head as if looking streight forward and hold the piece up. 

Have a CT scan of your neck taken and ask your physiotherapist for thorough neck examination.

Make sure you got the right and good quality tools.

 

Take pictures at each disassembly stage if working on unfamiliar piece. 

If ths piece is givng you a hard time, leave it alone till later.

Don,t lend your good tools.

Get a new H/S if the old one  reminds you of macaroni sauce.

 

  • Like 2
Link to comment
Share on other sites
  • 3 weeks later...
Tmuir Distinguished Member

Tmuir

Posted
Posted

Unfortunately I don't have any photos, that was only some of the damage that was done to the watch, the whole movement was a right off. They also lost the hairspring, lost the regulating leaver, broke the jewels on the balance bridge, cracked the glass, lost the winder and tried to bush 2 pivot holes on the bridges and just trashed the bridge.

But very kindly they told the owner there was no charge for the service...............

  • Sad 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mikepilk
      Setting lever spring

      By mikepilk · Posted

      The stress is the force (on the spring) x distance. The maximum stress is at the bottom, and decreases up the arm. That's why they always break at the bottom. I used a round file, then something like 2000 grit to finish. I gave the rest of the arm a quick polish - no need for a perfect finish. Just make sure there are no 'notches' left from cutting/filing. The notches act like the perforations in your toilet paper 🤣
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      It's probably a cardinal rule for watch repair to never get distracted while at the bench. Yesterday, after finishing a tricky mainspring winding/barrel insertion (I didn't have a winder and arbor that fit very well) I mentally shifted down a gear once that hurdle was passed. There were other things going on in the room as I put the barrel and cover into the barrel closer and pressed to get that satisfying snap. But when I took it out I realized I never placed the arbor.  When opening a barrel, we are relying on the arbor to transfer a concentrically-distributed force right where it is needed at the internal center of the lid. However, when that isn't present it's difficult to apply pressure or get leverage considering the recessed position of the lid, the small holes in the barrel and the presence of the mainspring coils. It was a beat-up practice movement so I didn't take a lot of time to think it over and I pushed it out using a short right-angle dental probe placed in from the bottom, but that did leave a bit of a scratch and crease in the thin lid. I had also thought about pulling it using a course-threaded screw with a minor thread diameter smaller than the lid hole and a major diameter larger, but that may have done some damage as well.  Thinking about how this might have been handled had it been a more valuable movement, is there a method using watchmaking or other tools that should extract the lid with the least damage? 
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      🤔 what happens if lubrication is placed directly on top of epilame ? Making a small groove so the lubrication doesn't spread across the component but what if when lubing a little overspills and sits on the epilame .
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Why just the bottom mike ? Is it worth polishing the whole arm ?
    • mikepilk
      Setting lever spring

      By mikepilk · Posted

      The one thing I took time over was to round and polish the curves at the bottom of the jumper arm. The slightest mark (left over from cutting of filing) acts as a stress raiser, just where you don't need it. 
×
×
  • Create New...