Jump to content

Vostok Generalskie


VWatchie

Recommended Posts

Finally finished my Vostok Generalskie extensive overhaul:

43202687415_79ce7d8380_o.jpg

43202686745_b958879982_o.jpg

43202686485_02de33f6d2_o.jpg

43390959984_4863311416_o.jpg

43202687695_553575ba8a_o.jpg

No other watch have I serviced, cleaned, polished, and lubricated as meticulously as this Vostok Generalskie; the movement, case, dial, hands, and crystal. Case and crown gaskets were of course replaced and silicone greased. I even cleaned and polished all train wheels by hand (a bit over the top, I know, but I just couldn’t help myself).

I had many good reasons to be thorough though; This Generalskie was a spontaneous gift to me from someone who made a deep impression on me (I’ll always remember you T). I think it’s one of the most impressive looking Vostoks I’ve seen, and I just love that dolphin case back lid. And, it was my first serious attempt to (somewhat) understand and successfully service a 31 jewel automatic watch.

The service spawned some pretty interesting discussions on WUS and watchrepairtalk.com. First, it was established by our "comrade" experts over at WUS in the “Q&A Expertise thread: Is this watch legit or a Franken?” that it is indeed legit. The first and major challenge for me was to understand how to service the automatic mainspring barrel. As I learned, this is not entirely trivial when it comes to automatic watches (thank you all!). Secondly, I was puzzled by the state of the reversing wheels and how to lubricate them. This too was eventually sorted out.

For my personal use, I made a "reassembly plan" using pictures from the disassembly. It was only meant for me personally, but for anyone interested click here. I should mention that during the assembly I figured out that it would be most convenient to assemble the parts for the automatic winding as late as possible, so this does not show in my "reassembly plan".

The quality of the movement and the entire watch is the best I’ve seen in any Vostok, Raketa, or Poljot so far. The movement contained some surprising details I haven’t seen before. The centre wheel held a very small (micro) brass cylinder right in the centre of the arbor to hold or guide the seconds hand pivot (see the picture below). Let me tell you, it was not easy to handle, not even with my finest tweezers. Most shims, like under the balance cock, were gilded, and so on. I believe this watch was meant for export and made to impress. It was sold in Stockholm, Sweden sometime in the early 90-ties.

43905551001_c27fa73ef2_o.jpg

I wear it with pride! :biggrin:

 

Edited by VWatchie
  • Like 6
Link to comment
Share on other sites

It truly looks absolute pristine !! I initially thought that you were pulling wool over our eyes and presented a brand new watch :startle:

Also congrats with servicing your first 31-jewel automatic, surely more to come ....... :thumbsu:

It looks stunning in every sense and it comes even with a matching strap....... I would wear it with pride too !

Hats off !!   :Bravo:

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.       I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • Hello and welcome from Leeds, England. 
    • Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.    
×
×
  • Create New...