Jump to content

Advice on a Zenith Cleaning Machine

Landman
 Share

Recommended Posts

Landman New Member

Landman

Posted
Posted

Hello I just purchased a vintage Zenith Champion watch parts cleaner and this is my first parts cleaning machine to own and use. The seller said it works has forward, reverse and heater dryer but that it has no been used in a while so it could use servicing. I got a really good deal on this I'm not sure if it's a good brand or not. I know a little bit about working on electronics but I don't know much about this machine it looks really simple inside. I am wondering what I should do if anything so I can start using it and not have to worry that something should happen. The wires outer material at the top has a slice in it and the cord has been replaced spliced into the old rather than soldering it to the switch. Should I replace the wiring or will just wiping down the machine with some light detergent be sufficient. If anyone has some advice I would much appreciate it. Thanks Much Landry

s-l1600.jpg

Photo Jul 26, 1 02 52 PM.jpg

Photo Jul 26, 1 02 22 PM.jpg

Photo Jul 26, 1 02 31 PM.jpg

Link to comment
Share on other sites
  • 2 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Movement inserted from crytal side

      By oldhippy · Posted

      Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
×
×
  • Create New...