Jump to content

Abrasives with Screwhead Polisher


sstakoff

Recommended Posts

Recently acquired a beautiful screwhead polisher:

polisher.thumb.jpg.bb6be4d0960084a0ff6208fe28d1a449.jpg

 

The polisher came with two jars of abrasive powder. One is carborundum and the other diamantine. I am looking for some guidance as to which abrasive gets used on which lap and advice on how to charge the lap. There is a steel lap, a brass one and finally a wooden one.  Thanks in advance!

 

  • Like 2
Link to comment
Share on other sites

Diamantine and carborundum come in different grit sizes, you'd naturally want coarsest on the steel, medium on the bronze, and finest on the wood. 800 grit for coarse, 1200 or so for the middle, and to finish I like 1 micron diamond paste (about 14000 grit) would be my recommendation. Maybe even a little coarser for the steel if you want. Seems like a big jump at the end but in my experience works well. When I frequently used my similar tool I made up a tin lap to replace the wood. Now I use a tripod tool with 12 micron paper on glass to flatten, and 1 micron diamond on a tin lap. I find it's much faster than the above tool.

  • Like 1
Link to comment
Share on other sites

1 minute ago, nickelsilver said:

Diamantine and carborundum come in different grit sizes, you'd naturally want coarsest on the steel, medium on the bronze, and finest on the wood. 800 grit for coarse, 1200 or so for the middle, and to finish I like 1 micron diamond paste (about 14000 grit) would be my recommendation. Maybe even a little coarser for the steel if you want. Seems like a big jump at the end but in my experience works well. When I frequently used my similar tool I made up a tin lap to replace the wood. Now I use a tripod tool with 12 micron paper on glass to flatten, and 1 micron diamond on a tin lap. I find it's much faster than the above tool.

Thank you. I will check the grit sizes when I get home tonight. Assume you mix the powder with oil -  If so, any recommendations o=n type of oil?

Link to comment
Share on other sites

I've never heard the reason behind it but knowledgeable and experienced polishers have always told me it's better to use a good vegetable oil than a mineral oil. Colza is a good one. Nothing disastrous is going to happen if you use a thin machine oil though.

On the coarse laps the oil/abrasive can be rather wet, but on the final lap you want to rub it on and in with a clean finger or cloth, leaving a distinct layer but it should almost be dry. If it's wet the abrasive will clump together and ball up giving fine scratches along with the polish.

Link to comment
Share on other sites

2 hours ago, sstakoff said:

Recently acquired a beautiful screwhead polisher:

polisher.thumb.jpg.bb6be4d0960084a0ff6208fe28d1a449.jpg

 

The polisher came with two jars of abrasive powder. One is carborundum and the other diamantine. I am looking for some guidance as to which abrasive gets used on which lap and advice on how to charge the lap. There is a steel lap, a brass one and finally a wooden one.  Thanks in advance!

 

    Very good!    what do you do if the screw slot is buggered up?

Link to comment
Share on other sites

1 hour ago, nickelsilver said:

I've never heard the reason behind it but knowledgeable and experienced polishers have always told me it's better to use a good vegetable oil than a mineral oil. Colza is a good one. Nothing disastrous is going to happen if you use a thin machine oil though.

On the coarse laps the oil/abrasive can be rather wet, but on the final lap you want to rub it on and in with a clean finger or cloth, leaving a distinct layer but it should almost be dry. If it's wet the abrasive will clump together and ball up giving fine scratches along with the polish.

   I use synthinic (sp) oil,   veg. oil can mold.   the viscosity to use is the real question.  vin

Link to comment
Share on other sites

When you get to using it you have to make 110% sure you've cleaned the screw perfectly when going from one lap to the next. Otherwise you'll contaminate the lap and it will need to be resurfaced. Artist's gum eraser and old rodico do pretty well, finish with pithwood and a friendly solvent like isopropyl alcohol. It's tedious but less tedious than redoing the lap.

  • Like 1
Link to comment
Share on other sites

  • 3 weeks later...
    Very good!    what do you do if the screw slot is buggered up?
Depends, if the slot isn't beveled then simply polishing the head takes care of any raised burrs and makes the head look tidy again. You could run a screwhead file through it if really going for perfection.

On beveled heads a very fine cut square escapement file works well. Like a 6 cut or 8 cut if you have it. The file finish blends visually with the polished head and looks polished. A square degussit stone can also work but they often are too rounded at the corners. To keep the file centered in the slot leave the screw in the polishing tool, it will rotate slightly as needed keeping the file on track. If not using the lathe type polisher you can rest the screw in a bench block so it's supported by the head and the screw will align itself with the file.
Link to comment
Share on other sites

8 minutes ago, nickelsilver said:

Depends, if the slot isn't beveled then simply polishing the head takes care of any raised burrs and makes the head look tidy again. You could run a screwhead file through it if really going for perfection.

On beveled heads a very fine cut square escapement file works well. Like a 6 cut or 8 cut if you have it. The file finish blends visually with the polished head and looks polished. A square degussit stone can also work but they often are too rounded at the corners. To keep the file centered in the slot leave the screw in the polishing tool, it will rotate slightly as needed keeping the file on track. If not using the lathe type polisher you can rest the screw in a bench block so it's supported by the head and the screw will align itself with the file.

   good show;  to de burr the slot.  I use a hone stone.  they are available in small triangle  or  small flat,  course or fine .  oil,  water or dry  vin.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • 🤔 leaving the EU meant that UK was no longer part of the convention and have already been turned down an independent reapplication. I'm pretty sure courts have to be held in Switzerland in this case. There will be a lot more watches stashed away in draws  tbh, folk wont be able to afford to maintain them. Cheap watches will be bought and top end watches by folk with plenty of cash that can pay for service and repair. The expensive once in a lifetime gifts and everything else inbetween will be at the forgotton when they stop working. I know i was being a numpty, get used to it 😄 Anybody that knows will boycott them, but besides repairers who will know. Nope will never buy one, i made that decision as soon as i learnt about this. 
    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
×
×
  • Create New...