Jump to content

Back to being a member

jdm

By jdm
in Help & Support With This Website

 Share

Recommended Posts

Tmuir Distinguished Member

Tmuir

Posted
Posted

Being a mod is a thankless task. I helped mod a forum on toy steam engines for around 10 years, and although a small number of members realise just how much you do, many see you as 'the forum police' there to ruin everyone's fun, so fully understand stepping back to being just a member.

Thanks for the work you did during your time as a mod

  • Thanks 1
Link to comment
Share on other sites
dadistic Distinguished Member

dadistic

Posted
Posted

Thanks JDM, I've watched you deal  unmercifully with spammers, and applauded from my chair. Although I found that I didn't agree with some of your approaches, they where the lesser part of what an admin does, and your constant attention to the forum helped it quite a bit.

Admin is a thankless job, and it's not often obvious what goes on until it's not happening anymore. Hope the other admins can take up the slack.

Thanks Again!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      My first Gruens. Precision 510 and N510R movements.

      By rjenkinsgb · Posted

      Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...