Jump to content

Seiko 7548. . rescue


Recommended Posts

Hi guys..

I don't really like working on quartz watches but I do make an exception for the Seiko 7548. I came across this at a flea-market for MYR20 (USD5) so I figured I'd try to get it working. Its actually a 7546 but theres not much difference. The 7548 has five jewels and the 7546 has to make do with only four.

The hands have the usual black stuff which is what remains of the original lume. First thing I checked is if the hands set, unfortunately it only does part of the way. Forwards the minute hand sticks at the 50 minute mark and backwards it gets stuck around the hour mark. Day date sets ok.

IMG20180729132436.thumb.jpg.badee8a60c1ab8305bb1c3c73e9efa5a.jpg

Typically grotty caseback. This is a 7546-7130

IMG20180729132445.thumb.jpg.07fbac51d703564bb496bc58834d52ff.jpg

It has a full length bracelet.. that's good!

IMG20180729132456.thumb.jpg.16b0deac1a487ccda37bc85bc977ff6c.jpg

What's not so good is the amount of dirt. Those with a weak stomach should look away now.

IMG20180729132623.thumb.jpg.4eca3939385f22736ee4b7441f35cd77.jpg

IMG20180729132629.thumb.jpg.544046c43ed7340e3f72d69c2f9dbe79.jpg

I finally open the caseback and look inside.... what I see is usually enough to throw it into the bin.

IMG20180729132751.thumb.jpg.ba52486845a2bd77d9f82517f9994523.jpg

The battery needs to be physically pried off as the corrosion has made it stick to the movement. Once removed I find this. The corrosion is pretty bad but I've seen worse. In this case the two contacts for the battery are still present and stand up to the prods from my tweezer. Sometimes they are corroded beyond use and break off.

IMG20180729132859.thumb.jpg.8112e5aa47862f2277eebc9a6759eaea.jpg

The dial resembles a starry night sky. You'd pay a lot of money if this was a high end swiss watch but this is bassically a reaction from the cases released when the battery acid oxidises. That sh\t wont buff out.

IMG20180729133327.thumb.jpg.b51143a2f97705bd7adfbd757dde5c34.jpg

The stuff under the dial is the same as on the 6309 automatic movement. Looks good so far.

IMG20180729133948.thumb.jpg.603f54be76ab01ab93dc1c07ee5e6253.jpg

But the hour wheel was stuck to the cannon pinion and thats was what made setting the hands impossible. When this happens the keyless works usually suffer broken/worn teeth as people try to force the crown around. Those parts on this watch look ok.

Here we have a picture of the underside of the date advance. The date advance is made of plastic so its in pretty ok condition but the mainplate has a lot of corrosion.

IMG20180729134508.thumb.jpg.18c2a01c3b73bf3b22b43998ea7b80c2.jpg

IMG20180729134338.thumb.jpg.ebde334b06882d7b41494a9ca2bc60c5.jpg

Next off is the circuit block. More corrosion (the black stuff).. it can be scraped off with pegwood.

IMG20180729135135.thumb.jpg.431d4565f32a9a432512261bed97e1de.jpg

And the coil is carefully lifted out and put away safely.

IMG20180729135155.thumb.jpg.993006714f2ac6cb374436a4afa326b1.jpg

Here we can see the effect of the battery juices on the watch mainplate. train bridge is heavily discoloured and most likely the pivots as well but its in the battery cavity that the corrosion is heaviest.

IMG20180729135208.thumb.jpg.9f0db079db18802fa81bad839266875d.jpg

The (+) contact (held by screw) shows sign of corrosion. If this breaks off the movement is not worth repairing.

IMG20180729135358.thumb.jpg.7a807b00c44f5052258b4b641dc951a0.jpg

but luckily it comes off in one piece.

IMG20180729135640.thumb.jpg.d5d826b70ed3fb2f48b55429e441ade1.jpg

I finally remove the train bridge and lift it off. I made a mistake here as the stem is out and the movement is 'hacked' with the hacking part contacting the wheel. Mot really a problem but more important to remember this for the assembly. The wheels are stuck in the pivots so thats not good. Need to inspect them carefully to see if they are reusable.

IMG20180729140121.thumb.jpg.883b027218912e979c52fec37b08cd1e.jpg

Reference pic to show how the various wheels go together.

IMG20180729140358.thumb.jpg.852bedf6616ac84c409fd6dc1060942d.jpg

Bare mainplate ready for cleaning

IMG20180729141019.thumb.jpg.b6711c1da7fd6b96c44d386606ef32ad.jpg

 

So is the watch worth fixing? Frankly no. The dial is beyond salvage, the damage to the wheel pivots may affect the performance of the watch (surprisingly the pivots look good at high magnification) but the most important issue is the coil and circuit board. They are no longer available from Seiko and this particular watch is never going to be worth the money to source one from other sources.

Having said that.. I will check the coil and circuit board and if they are in working condition then I will re-install it and use the watch for a while. Even if I do get the watch to work, I foresee that the eventual fate of the movement will be as a donor for a 7548 diver watch as this seems to be the only quartz watch still in demand.

Will post updates.

 

 

 

 

 

 

IMG20180729135221.jpg

IMG20180729141855.jpg

IMG20180729163815.jpg

IMG20180729163858.jpg

Edited by anilv
  • Like 4
  • Thanks 1
Link to comment
Share on other sites

Hope not@anilv as I want to see how this project comes out mate! There’s not enough people working on my lovely Seiko’s on here so I appreciate it when people show their work so I can learn from them.


Sent from my iPad using Tapatalk

  • Like 1
Link to comment
Share on other sites

Brilliant. I found a similar Seiko, it was 50 cents at a market. 7546 movement, nearly identical.
It had a stuffed crystal. absolutely filthy case/movement back, corroded battery, etc, etc. Missing end link from strap.
However after cleaning it gently and using rodico on the dial, I was able to create a wonderful watch worth wearing.

The patina on the dial is just amazing. The green oxidation from the plated crystal ring and the brown rust from the crown wheel/keyless make it look like a oyster shell. Really nice look. The only problem is the movement number got worn off the dial, but you can still see JAPAN MADE.

I havent  stripped the movement yet but I blew it out and oiled it with 9010 and has been running +1 sec/day for nearly a year now.

The crystal cost a whopping $3 from Cousins. End link was 25 cents.
 

IMG20180806201420.jpg

Link to comment
Share on other sites



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Never and others. Yes like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • Get someone local to tig it ,very easy fix and should only take a few minutes so probably wouldn’t cost much ,or failing that get it very clean and silver solder it. Dell
    • Hi, The winding pin is not split, well that's how it was when I obtained the watch. The movement is front-loaded and here's a picture of where the case screws are fitted. The face picture is before I dismantled it.
    • I dont think mine is. Its an idea to have them all in one place if possible, then a quick screenshot will have them saved. Unless anyone has any other ideas of how to reconnect 
    • My email address is in my profile, feel free all to drop me a quick hello. 
×
×
  • Create New...