Jump to content

Mostly Russians, and few Japanese and Swiss


VWatchie

Recommended Posts

Careful examination of the stub of "gold" to the left might give some clues. It looks as though there was a metal tab attached to that, and floating on that plastic washer, but that may now be missing.

If you had another mech to compare, obviously that would be a help.

Maybe try a small copper wire screwed to that left hand screw and placed on top of the plastic washer, then refit the battery and see if it springs to life.

Link to comment
Share on other sites

Also take a look at this pic. of a similar mechanism.

I suspect that Timpsons are fitting the battery incorrectly.

The left hand screw/gold plate, needs careful cleaning, and the right hand tab needs fitting *UNDER* the battery, but above the plastic washer, and insulated in such a way that it doesn't short out the cell at the edge, so perhaps it just needs bent correctly to be recessed in at the right hand side of the battery holder to avoid contact with the edge of the battery. In other words the +ve of the battery looks to be connected to the left hand contact, and the -ve appears to be connected to the right hand contact (avoiding shorting things out in the process). The cell is an SR920SW, which are cheap as chips.

 

600x615xpoljot_quartz_1980s4.jpg.pagespeed.ic.TTlml-5PBX.jpg

Link to comment
Share on other sites

On ‎1‎/‎5‎/‎2019 at 6:58 AM, BUSAKAZ said:

Hi Andy thanks for the advice I’ll give it a go when I get a min and report back.

Thanks Kaz


Sent from my iPhone using Tapatalk

Hi all an update, after completely stripping the movement it was completely covered in battery gunk so put the parts in the cleaner and new battery and all is well :thumbsu:

  • Like 2
Link to comment
Share on other sites

I've now been wearing my red and black radio room Amphibia/Albatros (first picture of the first post in this thread) for exactly one month since I last regulated it (Vostok cal. 2409 manual). December 27th it was 29.5 seconds late, and today it's 32.5 seconds late. It has lost three seconds in a month! It's been a long time since I wore a quartz watch, but as I remember it, those weren't much better than that over time. Of course, it largely depends on how the watch is worn, stored and wound, but nevertheless, I'm "blown away"! Who said Russians weren't up to the Swiss!? ;)

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Look carefully at the tube end?? It appears to me to have a fragment thread visible? Either that or a step just away from the end? I can imagine a chamfer, but a step seems odd - but I've never seen the tubes used on these.
    • This is a very valid point and a subtlety that I was unaware of until fairly recently, learning all the time, the video below explains this point well:  
    • You don't have to use his special tester. Any good multimeter would work.
    • Yes, it looks like GT Revue 30. Doctor, You can not replace escape wheel by the dimensions You listed. One needs to know much more things like number of leaves of the pinion and it's diameter, the position in high of the table and the pinion, the hight between the pivots, the exact pivots diameter... And then, even if suitable wheel is found, one will need to know how to adjust the pallets position correctly. Restoring antique movements is something different than replacing parts. In older movements parts are not interchangeable, this means spare parts do not exist. Here the case is different, but still escapement adjustment will be needed if a wheel from a donor is found. So may be it will be easier to restore the donor for You...Restoring antique movements usually means making of the parts needed and this requires knowlage and working on lathes skill. In this case repivoting of the wheel is the natural solution, but there is a long way that one must walk untill getting ready for such work.
    • I was looking at Essence of Renata, a chemical used a lot for cleaning hairsprings: "Specially prepared solution for degreasing watch and instrument components. Indispensable for degreasing hairsprings." Looking at the MSDS you can see this is just pure n-Heptane, so could be an option for those who don't want to use the chlorocarbons or hexane?     HF6013 - Horological Essence COSHH Safety Data Sheet Horological Essence_0.pdf
×
×
  • Create New...