Jump to content

Proper technique for removing crown from stem?

Giannifive
 Share

Recommended Posts

Giannifive New Member

Giannifive

Posted
Posted

I'm assembling my first watch from components, and I have what is probably a basic question: What is the proper technique for removing the crown from the stem?  I'm trying to get the service crown off the stem of a new movement.  I'm using a pin vise to hold the stem, but it just spins as I try to unscrew the crown.  I'm not clamping with a lot of force, out of fear of destroying the stem.   Is there some trick to this?

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

The crown of the service stem is not really supposed to be removed, as it's made of grippy plastic and could be even glued.

Another stem should be provided with the mov.t, or bought separately. 

If you want to reuse the service stem see if you can just cut it to length, otherwise heat the stem a little and grab it with ridged pliers near to the crwon.

  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Hold the stem with your pin vise where the arrow is pointing and tighten right up. Then unscrew the button. New movements come with the plastic buttons so they can be tested winding up the normal way before they are sent out to the customer. There is no reason why you cannot use the stem. It is a waste of money buying another. 

Watch Stem.jpg

  • Like 3
Link to comment
Share on other sites
vinn3 Distinguished Member

vinn3

Posted
Posted
7 hours ago, jdm said:

The crown of the service stem is not really supposed to be removed, as it's made of grippy plastic and could be even glued.

Another stem should be provided with the mov.t, or bought separately. 

If you want to reuse the service stem see if you can just cut it to length, otherwise heat the stem a little and grab it with ridged pliers near to the crwon.

    yes,  "ridged pliers" for stem flats.  the parallel   jaws of the pliers grip the flats of the stem,  or a pinvise for round area of the stem.  best to buy a new stem.  vin

Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted

What Oldhippy suggested is the traditional method. Hold the pin vise in a bench vice if you need to tighten it more. You can grip the flats of the stem, but it’s a weak point, so that can potentially snap there. 

Link to comment
Share on other sites
Giannifive New Member

Giannifive

Posted
  • Author
Posted
19 hours ago, oldhippy said:

Hold the stem with your pin vise where the arrow is pointing and tighten right up. Then unscrew the button. New movements come with the plastic buttons so they can be tested winding up the normal way before they are sent out to the customer. There is no reason why you cannot use the stem. It is a waste of money buying another. 

Watch Stem.jpg

Thanks for the detailed response!  Once I realized where exactly to clamp and that I should "tighten right up" I was able to get the service crown off easily.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
×
×
  • Create New...