Jump to content

Proper technique for removing crown from stem?

Giannifive
 Share

Recommended Posts

Giannifive New Member

Giannifive

Posted
Posted

I'm assembling my first watch from components, and I have what is probably a basic question: What is the proper technique for removing the crown from the stem?  I'm trying to get the service crown off the stem of a new movement.  I'm using a pin vise to hold the stem, but it just spins as I try to unscrew the crown.  I'm not clamping with a lot of force, out of fear of destroying the stem.   Is there some trick to this?

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

The crown of the service stem is not really supposed to be removed, as it's made of grippy plastic and could be even glued.

Another stem should be provided with the mov.t, or bought separately. 

If you want to reuse the service stem see if you can just cut it to length, otherwise heat the stem a little and grab it with ridged pliers near to the crwon.

  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Hold the stem with your pin vise where the arrow is pointing and tighten right up. Then unscrew the button. New movements come with the plastic buttons so they can be tested winding up the normal way before they are sent out to the customer. There is no reason why you cannot use the stem. It is a waste of money buying another. 

Watch Stem.jpg

  • Like 3
Link to comment
Share on other sites
vinn3 Distinguished Member

vinn3

Posted
Posted
7 hours ago, jdm said:

The crown of the service stem is not really supposed to be removed, as it's made of grippy plastic and could be even glued.

Another stem should be provided with the mov.t, or bought separately. 

If you want to reuse the service stem see if you can just cut it to length, otherwise heat the stem a little and grab it with ridged pliers near to the crwon.

    yes,  "ridged pliers" for stem flats.  the parallel   jaws of the pliers grip the flats of the stem,  or a pinvise for round area of the stem.  best to buy a new stem.  vin

Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted

What Oldhippy suggested is the traditional method. Hold the pin vise in a bench vice if you need to tighten it more. You can grip the flats of the stem, but it’s a weak point, so that can potentially snap there. 

Link to comment
Share on other sites
Giannifive New Member

Giannifive

Posted
  • Author
Posted
19 hours ago, oldhippy said:

Hold the stem with your pin vise where the arrow is pointing and tighten right up. Then unscrew the button. New movements come with the plastic buttons so they can be tested winding up the normal way before they are sent out to the customer. There is no reason why you cannot use the stem. It is a waste of money buying another. 

Watch Stem.jpg

Thanks for the detailed response!  Once I realized where exactly to clamp and that I should "tighten right up" I was able to get the service crown off easily.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Malocchio
      Is this pallet fork over-locking?

      By Malocchio · Posted

      The entry jewel's not as bad but seems still too much lock. I do epilame the escape wheel and pallet jewels, then run dry for about 15 minutes, then put 9415 in exit jewel very little at a time and check with backlight how the oil's distributed.  Another question is about capped escape wheels. Should I somehow wear the epilame off the pivots before installing the wheel? I normally let the escape wheel run dry for that said 15 minutes when there's no cap jewel.
    • Malocchio
      Bezels - What am I doing wrong?

      By Malocchio · Posted

      Sometimes there's a certain place under the bezel where the case knife is supposed to be placed. In this borrowed pic there's a small crack at 3 o'clock. 
    • Waggy
      Bezels - What am I doing wrong?

      By Waggy · Posted

      Hi my fellow forum addicts, I'm writing this as I seem to have a hole in my knowledge (probably one of many!) I seem to have a horrible time removing bezels from watches. I am talking about the rotating type on sports/diving watches. I see many videos where the guy on screen barely inserts the case knife under the bezel and with no effort it pops off easily, then at the end it clicks back into place by hand with no effort. I am sure that part of this is due to skillful video editing, but I seem to wrestle with them, I have tried case knives and  even when using the tool below, I tighten it up in several positions and nothing happens. On a many occasions I have even warped the bezel in my attempts to remove it. Similarly, I have issues replacing bezels after cleaning etc. and often they have to be replaced using a press tool and inevitably are far too tight and will not rotate or loose to the point where they fall off or loose their click (perhaps due to micro warping when I tried to remove??). It is now to the point where I am actually avoiding watches with bezels as my success rate with them is terrible......please help!! In short I am asking: What am I doing wrong? What is the best method for removing bezels - how do you do it? What is the best method for replacing bezels - how do you do it? Any tips or tricks? Thanks  
    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Amplitude still seems low, but I'm going to let it run in a bit and revisit. Meanwhile, got the first layer of the calendar works together and made sure the date ring snaps to both in quickset and regular setting. The mechanism is pretty cool, so I took a video.  
    • AliCat
      Hello!

      By AliCat · Posted

      This is the part that need replaced if anyone can point me in the right direction. 
×
×
  • Create New...