Jump to content

First clock repair...How do I open it?

ftwizard

By ftwizard
in All Things Clocks

 Share

Recommended Posts

oldhippy Distinguished Member

oldhippy

Posted
Posted

You now need to remove it from the case. That inside ring should just pull our, unscrew the feet and the top and push from the front. Once removed can you show me a photo around the spring to include the click, as some of these types do not have a normal click spring and click.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

That is just what I expected to see. You cannot un-wind the springs in these movements. If you try and lift that circle shape which is the click, you will distort it and it will not wind up. Can you un pin the balance and take it out and show me please. It looks like the h/spring is damaged, if that is it is you might be able to repair in, oil the movement and see how it goes.

Link to comment
Share on other sites
ftwizard WRT Addict

ftwizard

Posted
  • Author
Posted
18 minutes ago, Lenj said:

Hi you need to take the hand off first to get the face off, have you got a hand puller??

I use levers, but I wasn't sure if that one just pulled off.

The face seems to be fixed to the backplate, somewhere near the twelve o'clock area.

Link to comment
Share on other sites
ftwizard WRT Addict

ftwizard

Posted
  • Author
Posted
54 minutes ago, oldhippy said:

Don't remove that hand. That is the alarm hand, it is fixed to the alarm wheel behind the dial. The movement should come away by ether pins or screws or both. Depending on your skills that h/spring can be sorted.

Thanks. That's what I thought about the alarm hand. I just can't see how the face is fitted to the backplate. I can't see any screws or pins. 

The dial is free all the way round, except for a point in the twelve o'clock position, midway between the centre and the edge of the face. Could it just be double sided tape or something? although, it doesn't feel like it.

I can sort the spring out, no problem. I've found a picture of how it should look.

Link to comment
Share on other sites
ftwizard WRT Addict

ftwizard

Posted
  • Author
Posted (edited)
1 hour ago, oldhippy said:

Yes it would.

Do you think I can separate the two parts without stripping the top half first?

If I run the springs down, how would I go about removing them and re-installing after cleaning?

Edited by ftwizard
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

 

I do not recommend this. You could undo the plates by a little and remove the pallets. Make sure to add oil to all parts that will run. Be very careful not to bend any pivots (its soft metal) the train will run down, you can put a finger on the train to ease the run down. When it is down you can take it apart and clean. You should be able to remove both springs from there arbors. Take note of how and where the springs are attached, they should be open loop and attached to the pillars. When putting it back together make sure, the springs are attached to their arbors. So the movement is together and tightened down, wind the springs up and as you go you should be able to attach the open part of the spring over their proper pillars.

 

  • Thanks 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Pick a spot where to start, the higest part,

Take note of how and where the springs are attached, they should be open loop and attached to the pillars. When putting it back together make sure, the springs are attached to their arbors. So the movement is together and tightened down, wind the springs up and as you go you should be able to attach the open part of the spring over their proper pillars.

You will just have move the parts into their holes. You can screw down the nuts a little by little, to hold things in place, not to tight or you could damage pivots.

  • Thanks 1
Link to comment
Share on other sites
ftwizard WRT Addict

ftwizard

Posted
  • Author
Posted (edited)

Thanks for everyone's help, especially oldhippy. I managed to get it all back together again. Manipulated the balance spring back into some kind of spring shape, and it's running very nice now.

Most important, I learnt a lot for the next one.

Edited by ftwizard
  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      I'm going to be setting up a decent little workshop here at home.

      By Neverenoughwatches · Posted

      Its a big item Michael and a lot that could go wrong with the process of getting it to its new location. I once helped install one of these units into a conservatory that i had built. It was big and bloody heavy and took six of us to get it in safely. If you have sliding doors and you need to remove the whole frame then that may or may not go well. But i would advise getting a professional in if you have little knowledge on the installation of them. The glazing of the doors could well be 6mm laminated glass which again will be heavy very heavy if the glazing units are big. The glass would also need to be set up and packed correctly to open the doors properly more so if they are unframed and the sliders are upvc. Seems a shame but if no one is biting and that may be due to having no warranty i guess the only takers might be someone that installs them for a living and knows how to repair. If its fibreglass just be careful, i sometimes have to cut fibreglass baths out and they are nasty to work with . Thick gloves are definitely recommended,  not fun picking out fibreglass spells two days later that have started to go septic. Good luck with it all matey.
    • tomh207
      Gamblin Gamsol for cleaning?

      By tomh207 · Posted

      I don’t know anything about this product, however assuming you have it if you put a drop on a mirror or piece of glass lying flat on a table and leave it to evaporate if it leaves any sort of residue it is not really suitable for watch part cleaning.   Tom
    • Michael1962
      I'm going to be setting up a decent little workshop here at home.

      By Michael1962 · Posted

      Well I put the spa on Gumtree (selling service) to try and sell it as it only needs a recirc pump to get it going. However, it weighs circa 250kg, so there's 4 fairly strong guys, and I would have to remove the sliding door in the room completely to be able to get it out, as well as clearing out a multitude of potted plants and the Alfresco outdoor setting to be able to get it out. Then move nearly everything in the back of the garage to be able to push it through to the front of the house. I would also need to hire furniture skates to be able to shift it around as carrying it is out of the question. Then someone would need a trailer to get it to their place as you won't get it on the back of a ute. So, the only answer is, out with the reciprocating saw and cut it all up into manageable pieces. Crying shame as it is in really good nick. I was only asking $1,500 and only got two bites, but it would only take something to go wrong with removing the sliding door etc that everything I make on the sale could go out the door on repairs etc. It would have been nice to be able to turn it into tools etc, but que sera sera. I don't know about the rest of the world, but there just seems to be very little interest from people wanting to buy things secondhand.  
    • mikepilk
      Commando special

      By mikepilk · Posted

      I would like to see the movement. The watch is the movement. Anyone can print a name on a dial and sell it as "the maker".
    • VWatchie
      What are these Seitz B-Jewels?

      By VWatchie · Posted

      Thanks for your answers! There seems to be a contradiction between these two answers, so perhaps I need to clarify. The flat and convex jewels look identical on the side facing away from the pivot shoulder. That is, there is an oil reservoir. I don't know if that changes anything but I thought it was safest to clarify since I didn't include a picture of the jewels from the opposite side.
×
×
  • Create New...