Jump to content

Help With A Loose Vintage Minute Hand.

chrisbuxton27
 Share

Recommended Posts

clockboy Distinguished Member

clockboy

Posted
Posted

A controlled nip is required. For this reason I put them in a lathe collet and GENTLY tighten. It is really,really easy to go to far. You can use a broach but I recommend you put the broach in a vice so you have total control. 

Link to comment
Share on other sites
chrisbuxton27 Watch Enthusiast

chrisbuxton27

Posted
  • Author
Posted

Clockboy the type of minute hand I mean has no stem just a flat hand with a hole to push onto the minute wheel. So there is nothing to place in the lathe collet. I'm thinking a stake of some shape to to close the gap slightly but not sure which would do it. Maybe a stake used for setting jewel stones would do it but that's something I've not tried either.

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

Ok sorry did not read the post correctly. However I recommend to get hold of the Cousins catalogue and browse it.

There are lots of hands available , different styles etc.  You will need to know length,width hole size etc. Too small is Ok because you can broach the hole out to fit but to big I really don,t know a way around it. Using a staking set punch might be to much for a delicate hand. The cleaver boys (not me) would make another arbour with a fatter shaft or thin the minute arbour and put a sleeve on. But you need a watchmakers lathe and lots of skill which I do not possess.

Link to comment
Share on other sites
Charlie WRT Addict

Charlie

Posted
Posted

On a proper staking set you will find several hole reducing punches. The five blued punches with round polished ends are the ones I use to re-size hands. Smaller seconds hands as found on sub-seconds dials with tiny tubes I do with my set of pin vises. There are also other ways to accomplish this task, but I find these punches work well for me. I will post a photo shortly.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...