Jump to content

Putting crystal back on


Recommended Posts

So, I have a Seamaster Cosmic, I had someone else put it together, but I didn't have the right case at the time.  I've got the case now.  I'm trying to use the crystal press and it's little slider tool to put the crystal back in.  Is there some magic secret to doing this?  I put the crystal on the little slider thing.  Clamp down with the crystal press, tighten it.  I can see a lip around the bottom of the crystal, apply it into the case and start releasing pressure.  From the videos I watch, the crystal should be in.  Nope... not for me.  I've tried at least 6 or 7 times, never get it.  It feels like it's setting down in the case, but it just pops out every time.  I thought maybe I don't have it tight enough, a couple times I almost couldn't loosen the press because it was so tight.  Any guesses at what I may be doing wrong, or is there some magic trick?

Link to comment
Share on other sites

Out of curiosity. Are you talking about the claw tool ? The crystal press is an actual press.

If you're indeed talking about the claw tool keep in mind that it usually works on acrylic crystals only. And I believe it doesn't work on the ones with a tension ring.

Is the glass teh correct one for the case ? Is it OEM ?

Link to comment
Share on other sites

It does sound like he is using the claw type tool (crystal lift tool) as chopin has said the crystal press is that a press, i have a screw down one with different dies, i find it more controllable than the hand squeeze type myself, plus i have seen a couple of that type break in the past.

Link to comment
Share on other sites

Sorry, yes.  I'm using the claw tool.  It is a plastic crystal, I'm not sure if it is because of the doming of it, but it almost looks like a tension ring is built into the glass.  I think I have a press in a box somewhere, I'm a little afraid of it, and doing greater damage.

Link to comment
Share on other sites

I get what you are saying mate, have you a friendly watchsmith that you can go to to get advice and guidance?  If you have pop in to see him /her and ask them to help you put that crystal back in. I know you might think this is not teaching you how to do it yourself but believe me I have used mine for some really simple stuff that was bugging me, and they enjoy passing on their knowledge.

Them claw lifters also need to be used with the clamp to ensure the jaws all stay the same height on  the crystal, I sometimes have great success with these and at others ive cracked crystals left right and centre using them.

  • Like 1
Link to comment
Share on other sites

Good idea for now mate, none of us are trying to put you off having a go ok, but sometimes we all have to all skin for that little bit of help, ask your smith if he will help and show you how he does it, I know some dissappear into the back room and do little jobs, but see if he will run you through the process so you can be certain of how it's done, I always leave a drink for mine, its nice to oil the wheels ready for the next visit I pay him

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • glad it worked out, those ESA movements are obsolete but new old stock is still out there, now that you know the make/model you could also do a cross reference to see if something more current would line up with the dial feet and hands...for future use if needed 👍
    • I wish they would have done so in this case. The whole story went like this: I sent my speedmaster to an omega service center about 10 years ago (at that point of time I haven't even started watchmaking). After the watch came back to me it had only about 6 months wristtime until january 2024 (not fair for this nice watch but the other pieces of my collection want wristtime too 🙂). So my conclusion is that the barrel was already faulty when it came back from service, can't imagine that amount of wear in 6 months wristtime. In january 2024 the performance on the wrist was quite bad, so I decided to have a look by myself. I have to admit that I didn't check the barrel close enough as I thought it must be ok, couldn't have issues after official omega service. That was a mistake, I will learn from that. Follow the golden rule: Nothing is certain except death and taxes.
    • I am same as you oldhippy I won’t touch anything with a battery, I keep getting requests to but I just say I only do mechanical clocks, there are quite a few errors & omissions with the repair guide have a look at this. https://mb.nawcc.org/wiki/Encyclopedia-Subjects/Torsion-Clocks/Book:Horolovar-400-Day-Clock-Repair-Guide-10th-Edition-Errors-and-Updates
    • Nice experiment. As it will be no problem, please put a twice less mass (half of the two penies) and read the amplitude, will be interesting. I mean to determine what is the relation torque/amplitude.
    • parts touching that aren't supposed to touch definitely would cause an issue. there not supposed to be touching there supposed to be independent which means that @VWatchie is correct that the ratchet wheel has no effect on performance. so if the ratchet wheel in your particular case is touching that is definitely going to be an issue and needs to be addressed. did you know that the Swatch group service centers do not change mainsprings? Swatch group service centers have an infinite supply of spare parts so they just change the mainspring barrel the whole thing. Plus anything else the watchmaker doesn't like just gets replaced like anything related to the escapement they just replace the components because they can.
×
×
  • Create New...