Jump to content

7s26 ticking too quiet for timegrapher ?


dreja

Recommended Posts

Hello,

I'm wondering what is your experience with a 7s26 watch, when you put it on the timegrapher ? Does the ticking sound have enough volume, to be picked up by the microphone ?

I'm using a standard Chinese timegrapher.

When I put the whole watch on the microphone (for eg. my SKX007 or my colleagues seiko 5), the microphone has difficulties to pick up the ticking sound. If I put on only the movement without the case, there are no problems.

 

So I'm wondering where could be the problem:

The spacer between the case and the movement is plastic, which "isolates or weakens the sound flow" to the case ?

As the crown is located at 4 and the case is not symetric. The problem might occur because the edge of the case is not symetrically pressed to the microphone ?

 

I don't have issues with other "low volume ticking" watches or with bare movements without the case. So I hope my microphone works ok.

Thanks

Andrej

Link to comment
Share on other sites

10 hours ago, dreja said:

When I put the whole watch on the microphone (for eg. my SKX007 or my colleagues seiko 5), the microphone has difficulties to pick up the ticking sound.

That is divers' watch with a thick case and caseback, so maybe that is the reason.

However I have no problem at all getting a good signal on a closed 7S26-0020 with either a 1000 or 1900 model timegrapher.

Link to comment
Share on other sites

Hello,

thanks for the answers.

I've got a Timegrapher No. 1000, about 8 years old. It seems, that there are at least 2 versions of the No. 1000 model. The difference can be seen, when you switch on the display:

1st version shows the daily rate only on the top of the screen.

2nd version shows the daily rate also on the main screen in 4 different horizontal display sections.

 

I have also noticed that there are 2 types of microphone stands. One stands is more rectangular, while the other is more circular.

If you look at the back, there are two versions of Frequency calibration connector. One has a female BNC connector while the other has a usb square connector.

 

I've got the first version with a BNC connector and a rectangular microphone stand.

Unfortunatly my version has not the ability to adjust the microphone gain. The up/down buttons change only the contrast (both in capture mode and while stopped)...

 

Andrej

 

Link to comment
Share on other sites

I agree it's probably just the thickness of the case although there may be a method to adjust the sensitivity.  I've done some Seiko 7002's that had pretty thick cases and found that taking the case back off during testing was an acceptable workaround.

Link to comment
Share on other sites

8 hours ago, Pip said:

I think you can only adjust the mic gain on the 1900 version.

Yes, and on the 1000 model also as mentioned above.

However, using either model I have cheched literally hundreds of 7S26 watches with all types of cases and never had to adjust gain in order to pick a good signal.

Link to comment
Share on other sites

1 hour ago, jdm said:

Yes, and on the 1000 model also as mentioned above.

However, using either model I have cheched literally hundreds of 7S26 watches with all types of cases and never had to adjust gain in order to pick a good signal.

Oh, I'm probably wrong then as I thought you couldn't adjust gain on the 1000.

As an aside I've not had issued picking up any ticking and tocking from diver cased watches either so maybe it's a mic problem.

Link to comment
Share on other sites

Thanks for all answers, I have found the issue :)

The problem was, that I have put some Tesa adhesive tape on the one microphone's plastic part. I did this to avoid scratching the watch - without the protection tape I could see (with loupe) the small marks on watch case.

Without the protection tape it works ok :) Instead of the tape I can put a piece of paper or even a paper sticker (as on the photo) between the watch and microphone.

 

 

IMG_20180616_084902.jpg

Link to comment
Share on other sites

15 minutes ago, dreja said:

 I did this to avoid scratching the watch - without the protection tape I could see (with loupe) the small marks on watch case.

Very good, you're treating a $200 watch same as $2,000 one. Which can be justified by the OCD attitude of some owners.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Haha. You're just in a wicked mood today John 😅
    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
    • I have a PDF below that will help. The problem was the PDF wasn't designed for this purpose it was designed to tell you what size watch you  have. Then it doesn't take into account movements come conceivably in different thicknesses.   watch-ligne-size-chart.pdf
    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
×
×
  • Create New...