Jump to content

7s26 ticking too quiet for timegrapher ?


dreja

Recommended Posts

Hello,

I'm wondering what is your experience with a 7s26 watch, when you put it on the timegrapher ? Does the ticking sound have enough volume, to be picked up by the microphone ?

I'm using a standard Chinese timegrapher.

When I put the whole watch on the microphone (for eg. my SKX007 or my colleagues seiko 5), the microphone has difficulties to pick up the ticking sound. If I put on only the movement without the case, there are no problems.

 

So I'm wondering where could be the problem:

The spacer between the case and the movement is plastic, which "isolates or weakens the sound flow" to the case ?

As the crown is located at 4 and the case is not symetric. The problem might occur because the edge of the case is not symetrically pressed to the microphone ?

 

I don't have issues with other "low volume ticking" watches or with bare movements without the case. So I hope my microphone works ok.

Thanks

Andrej

Link to comment
Share on other sites

10 hours ago, dreja said:

When I put the whole watch on the microphone (for eg. my SKX007 or my colleagues seiko 5), the microphone has difficulties to pick up the ticking sound.

That is divers' watch with a thick case and caseback, so maybe that is the reason.

However I have no problem at all getting a good signal on a closed 7S26-0020 with either a 1000 or 1900 model timegrapher.

Link to comment
Share on other sites

Hello,

thanks for the answers.

I've got a Timegrapher No. 1000, about 8 years old. It seems, that there are at least 2 versions of the No. 1000 model. The difference can be seen, when you switch on the display:

1st version shows the daily rate only on the top of the screen.

2nd version shows the daily rate also on the main screen in 4 different horizontal display sections.

 

I have also noticed that there are 2 types of microphone stands. One stands is more rectangular, while the other is more circular.

If you look at the back, there are two versions of Frequency calibration connector. One has a female BNC connector while the other has a usb square connector.

 

I've got the first version with a BNC connector and a rectangular microphone stand.

Unfortunatly my version has not the ability to adjust the microphone gain. The up/down buttons change only the contrast (both in capture mode and while stopped)...

 

Andrej

 

Link to comment
Share on other sites

I agree it's probably just the thickness of the case although there may be a method to adjust the sensitivity.  I've done some Seiko 7002's that had pretty thick cases and found that taking the case back off during testing was an acceptable workaround.

Link to comment
Share on other sites

8 hours ago, Pip said:

I think you can only adjust the mic gain on the 1900 version.

Yes, and on the 1000 model also as mentioned above.

However, using either model I have cheched literally hundreds of 7S26 watches with all types of cases and never had to adjust gain in order to pick a good signal.

Link to comment
Share on other sites

1 hour ago, jdm said:

Yes, and on the 1000 model also as mentioned above.

However, using either model I have cheched literally hundreds of 7S26 watches with all types of cases and never had to adjust gain in order to pick a good signal.

Oh, I'm probably wrong then as I thought you couldn't adjust gain on the 1000.

As an aside I've not had issued picking up any ticking and tocking from diver cased watches either so maybe it's a mic problem.

Link to comment
Share on other sites

Thanks for all answers, I have found the issue :)

The problem was, that I have put some Tesa adhesive tape on the one microphone's plastic part. I did this to avoid scratching the watch - without the protection tape I could see (with loupe) the small marks on watch case.

Without the protection tape it works ok :) Instead of the tape I can put a piece of paper or even a paper sticker (as on the photo) between the watch and microphone.

 

 

IMG_20180616_084902.jpg

Link to comment
Share on other sites

15 minutes ago, dreja said:

 I did this to avoid scratching the watch - without the protection tape I could see (with loupe) the small marks on watch case.

Very good, you're treating a $200 watch same as $2,000 one. Which can be justified by the OCD attitude of some owners.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...