Elma Watch Cleaning Machine

[SSTEEL]

I know Mark has one of these machines, I recently purchased one myself, and its in dire need of restoring.  I have stripped it down, and wish to rewire it and replace the ageing motor speed switch with a modern alternative, so could really do with a wiring diagram if anyone has one?

[SSTEEL]

Its ok now, I have source one, should anyone else need a copy drop me a pm.

[Mark]

Hi Micky,

 

Have you found anywhere that would sell a new rheostat for the elma? Mine has little to no adjustment on the motor speed anymore. I have managed to set it at a manageable speed but it would be nice to ramp it up during the spin-off.

[SSTEEL]

Yes Mark, found a small alternative to the variable motor speed switch...

 

http://www.ebay.co.uk/itm/New-AC-50-220V-2000W-Motor-Speed-Control-SCR-Controller-Knob-Switch-/251665634527?&_trksid=p2056016.l4276

 

Also found complete new machines, one without timer, and another twitch timer for £299 and £399 each, but wheres the fun in that?  

 

Prefer to restore my own.  

 

For anyone interested in the new pieces, see below..

 

http://www.ebay.co.uk/itm/Watch-cleaning-machine-janta-pearl-brand-cleans-rolex-omega-tissot-2045-/111473300849?pt=UK_Jewellery_Watches_WatchAccessories_SpareParts_SM&hash=item19f4539571

 

With timer..

 

http://www.ebay.co.uk/itm/Watch-cleaning-machine-janta-pearl-brand-with-timer-cleans-all-watches-2047-/291253631038?pt=UK_Jewellery_Watches_WatchAccessories_SpareParts_SM&hash=item43d011b83e

 

Janter Branded.

Edited October 5, 2014 by SSTEEL

[SSTEEL]

What I would also like to replace is the motor, does anyone know a stockist for this particular motor?

[Mark]

Cheers Micky :)

[jnash]

I also have one of these elma cleaners, it seems that there is now a buzzing sounds and the switch doesnt really work, after long use there is a slight smell of burning. Im assuming i need to clean up the bearings in the motor and replace the switch.

 

I could probably figure out the switch,but wouldn't know how to clean up the motor bearings.

 

Any help would be appreciated.

 

Thanks

 

J

[Geo]

I wouldn't be over concerned about the bearings unless they are making a noise. The switch on the other hand will probably be what is making the buzzing sound. If you can't get the switch apart to clean the contacts, I recommend you get a new one sooner than later. In all honesty, you should replace the switch anyway.

Once you have replaced/repaired the switch, run the machine dry and hold the blade of a long screwdriver to the top and then bottom of the motor as close to the bearings as possible, and put your ear against the handle. You will be able to hear how good the bearings are. There should just be a gentle hiss, if they are screaming or rumbling, replace them.

[jnash]

Thanks Geo, i wil have a go when i get a chance

 

Jonathan 

[SSTEEL]

Well my Elma Super Elite is coming together slowly, I have removed all the old paint from the circular base, heater chamber, and motor cover so far with the timer housing and front fascia, and central pole clamp currently soaking in acetone ready for the refinishing.

 

 

Base..

 

Untitled by Micky.!, on Flickr

 

Heater chamber, and motor shroud..

 

ELMA SUPER ELITE REFURB by Micky.!, on Flickr

 

I have purchased what I think is the correct hammered blue paint, but I am actually now considering not painting it a colour at all, I might just clear coat it to give it that rustic look, undecided at the moment, so any opinions would be greatly appreciated.

Edited November 1, 2014 by SSTEEL

[Geo]

That's one hell of a thorough job your doing Micky, I'm looking forward to seeing the end result. Regarding finish, I think I would go with the blue hammered finish, I think it might be more durable and resistant to cleaning fluids.

[Mark]

I agree. Better to paint it. Really impressive so far Micky

Sent from my iPhone using Tapatalk

[SSTEEL]

Cheers guys, I guess you're right there, hammered blue it is then :)

[SSTEEL]

Acetone makes easy work of removing the old paint :)

 

Super Elite Parts Soaking in Acetone by Micky.!, on Flickr

[SSTEEL]

For anyone interested, this is where I get my acetone from.

 

http://www.ebay.co.uk/itm/Acetone-99-5-Pure-5-Litre-5L-/130542515028?pt=UK_BOI_Medical_Lab_Equipment_Lab_Supplies_ET&hash=item1e64f0b354

[Mark]

Thats very useful info - thanks for sharing.

 

I am sure Graham Baxter uses powder coating when he referbs the L&R machines - is that an option for you? 

I have never done powder coating so I don't know what is involved but I understand it is very durable.

[SSTEEL]

Ideally Mark, I would love to have it powder coated, but alas I know of nowhere local that offers this, so what I done is found a very close match blue, with hammered effect, its brush on Hammerite.  I just hope I manage to achieve a nice even coating with it.

Edited November 1, 2014 by SSTEEL

[Geo]

its brush on Hammerite.  I just hope I manage to achieve a nice even coating with it.

Hi Micky, for best results don't brush it, dab it on!

[bobm12]

Hi Micky,

 

Can you leave the bare metal finish (nickel)? or would it be a problem with durability? It looks good as it is!

[SSTEEL]

That was my original plan, and was going to spray it with clear coat to give it some durability.  I have since etched the surfaces now ready to paint blue, but I do like the idea of a satin finish which I can do with my wire wool.

[SSTEEL]

I placed the jars with new lids into the base just to give you an idea what it would look like if I were to clear coat it, the clear coat is a gloss clear lacquer, which was my preferred option.

 

SANY6881 by Micky.!, on Flickr

[clockboy]

My L&R refurbished by Graham Baxter was indeed powder coated. It gives the machine a really durable finish which is needed when dealing with chemicals. 

[bobm12]

Beautiful! But clockboy has a point! In any case it is a hell of a restoration! great job!!!

[SSTEEL]

Powder coating would be ideal, I agree, but I can't find anywhere local that can do it, but I would be prepared to ship the parts to the UK if needed to be coated. Anyone know if Graham Baxter would be willing to powder coat my parts?

[SSTEEL]

Final parts almost completed, just need to etch them next, then its on to the rewiring.

 

Untitled by Micky.!, on Flickr