Jump to content

Timex 1970 Marlin #25 - Pulled Hairspring


Recommended Posts

This evening I have begun to repair a 1970 Marlin Calendar and found the hairspring had been pulled.  A few years ago I would have avoided such a repair but

with time what once seemed impossible now has become easier.  So let me walk through the repair for you.

1. Here we see the hairspring has been pulled. Note the access window at 5 o'clock.  This window is to allow you to push out the brass wedge pin.

2. NOS hairspring \ balance assembly.

3. Wedge Pin

4. Remove the wedge pin and cap screw

5. See damage

6. 10 x view of the famous V conic end caps.  This is what made Timex stand out against other low end makers.

7. NOS parts ready to go to work

8. Note the bend at the tip.  As you rotate the balance this bend will first slip into the regulator.  Than it fits exactly into the bridge and held in place with wedge pin.

Just use fine tipped tweezers to help guide along the way.  What I like to do is keep the cap screw a bit tight so the spring stays in place.

9.Wedge back in and just give it a push to get it to seat. 

10 just a bit of room to allow me to shift the pallet fork back in place.  than just slowly screw down the cap.

11.  All done see the .MOV file at end

 

 

 

 

 

 

DSC08147.JPG

DSC08146.JPG

DSC08148.JPG

DSC08149.JPG

DSC08150.JPG

DSC08151.JPG

DSC08152.JPG

DSC08154.JPG

DSC08155.JPG

DSC08157.JPG

DSC08158.JPG

MOV08159.AVI

Edited by JerseyMo
  • Like 2
Link to comment
Share on other sites

Thank You.  A few adjustments to the workflow.

1) service movement prior to installing the new balance.

ammonia bath - 6 minutes in utra sonic - rinse in cold water - blow dry - 

lighter fluid bat - 6 minutes in ultra sonic - blow dry

2) re-fit balance = oil end caps

3) oil pivots

4) install winding parts after cleaning - 

5) continue the re-build

A few tips I've learned over the years:

- When letting down the mainspring, observer the winding gear for free and easy motion.  If it looks sluggish, remove it and inspect for dried grease, oil, wear. clean and replace as needed.

- test the time setting motion before installing the dial.  The hour and minute pinons can get tight and dry over the years.  If so, you should 

separate them and clean in fluid. than follow with very light lube and test again.

-  ditto for the winding lever and gears

- grease the stem tube and end of the stem. you will notice a much improved winding motion. This is especailly true when fitting a new stem crown.

- before installing the dial, be sure to bend the tabs back to a straight line.  It should look like and L, this way the tab

can be fully bent down to keep the dial correctly seated to the movement.

- inspect the case back seal - clean with cotton swab dipped in ammonia. "DO NOT" dip the case back into cleaner if there is an ink stamp inside.  This stamp indicates a two position production value and the last two digits are the year made.  Not terrible if you should loose the ink but just something to keep in mind that it has been there for maybe 50 - 60 years and use just wiped it out!

Well that about does it for now... 

 

BTW - the watch is running spot on time some 12 + hours latter.

 

  • Like 1
Link to comment
Share on other sites

I do not have a timegrapher only test is to match against the clock radio on the work bench.  The testing will also include a daily wearing to see how it holds up.  Like many collectors I will accept a degree of + - on accuracy.

Link to comment
Share on other sites

3 hours ago, JerseyMo said:

I do not have a timegrapher only test is to match against the clock radio on the work bench.

You can also use a mobile or PC app, there are many threads about that. It's really an indispensable tool because it shows you not just the rate but more fundamental health parameters like amplitude and pattern regularity.

Link to comment
Share on other sites

On 6/3/2018 at 9:08 PM, JerseyMo said:

This evening I have begun to repair a 1970 Marlin Calendar and found the hairspring had been pulled.  A few years ago I would have avoided such a repair but

with time what once seemed impossible now has become easier.  So let me walk through the repair for you.

1. Here we see the hairspring has been pulled. Note the access window at 5 o'clock.  This window is to allow you to push out the brass wedge pin.

2. NOS hairspring \ balance assembly.

3. Wedge Pin

4. Remove the wedge pin and cap screw

5. See damage

6. 10 x view of the famous V conic end caps.  This is what made Timex stand out against other low end makers.

7. NOS parts ready to go to work

8. Note the bend at the tip.  As you rotate the balance this bend will first slip into the regulator.  Than it fits exactly into the bridge and held in place with wedge pin.

Just use fine tipped tweezers to help guide along the way.  What I like to do is keep the cap screw a bit tight so the spring stays in place.

9.Wedge back in and just give it a push to get it to seat. 

10 just a bit of room to allow me to shift the pallet fork back in place.  than just slowly screw down the cap.

11.  All done see the .MOV file at end

 

 

 

 

 

 

DSC08147.JPG

DSC08146.JPG

DSC08148.JPG

DSC08149.JPG

DSC08150.JPG

DSC08151.JPG

DSC08152.JPG

DSC08154.JPG

DSC08155.JPG

DSC08157.JPG

DSC08158.JPG

MOV08159.AVI

well done !

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
×
×
  • Create New...