Jump to content

Portable DIY desktop workbench


jarz21

Recommended Posts

Currently having limited space to work on watches, I decided that a portable desktop workbench would be necessary for me. I was inspired by this blog post for a similar sort of DIY setup, but was having trouble finding good sources for the individual components. Instead I used the following parts (mostly ordered from Amazon but available at Home Depot and Target as well):

  • Carlisle CT121623 Café Standard Cafeteria / Fast Food Tray, 12" x 16", Gray
  • 1x IRIS Desktop Letter Size Medium Stacking Drawer model DTD-L (available in clear or black)
  • 2x IRIS Desktop Small Stacking Drawer model DTD-S (available in clear or black)
  • Velcro 90087 Sticky-Back Hook & Loop Fastener Tape with Dispenser, 3/4" x 5ft Roll, White
  • Everbilt #12 x 3/4in flat head phillips wood screws (SKU 284 773; from Home Depot)

I paid about $32 for all of the above. Interestingly, everything except for the wood screws was made in USA. The plastic drawers do come with clips that allow them to be attached together, but the connection seemed pretty weak (hence the wood screws).

To construct, I drilled through all of the holes on the bottom of the small drawers where the rubber feet would be pressed in (and ultimately ended up removing the Velcro you see in the picture below because I went with the screws instead):

20180330_161115.thumb.jpg.0e0f0a1e43e9921bf452b86373a1cccf.jpg

Next, I applied a bit of Velcro between the front edge of the two small containers. This may or may not have been necessary with the screws, but I did it anyway!

20180330_162759.thumb.jpg.3f862a797ca6adee3a3b9e0326ff6624.jpg

To attach the two small containers to the larger drawer, I removed the top panel of the latter, marked where all of the feet align, and drilled some more holes so I wouldn't crack the plastic by driving the screws through it. You'll see where the two front inner holes interfered with molded plastic, so I didn't use screws there (also why I used the Velcro in the picture above).

20180330_163343.thumb.jpg.6572181cb4c554601f8d0bb4d809c2af.jpg

20180330_163352.thumb.jpg.3195c8e057583b1a45ab1c3612039e0a.jpg

The screws may poke through the holes somewhat, but they shouldn't interfere with the drawers.

20180330_163423.thumb.jpg.4e18826e567e75dbe163fb2face9ee72.jpg

Next I used a utility knife to shave the low feet off the bottom of the tray to make it smooth, then marked where it would be centered on the top of the small drawers. And in case you had been wondering, I chose to use the tray because it was cheap and had a decent lip around the edge to prevent things from rolling off.

20180330_165742.thumb.jpg.63edbe1c265c7e3eb7665bc89d2b20f0.jpg

I then cut some lengths of Velcro in half and applied them to the topside of the small drawers. When I first ordered the Velcro, I hadn't planned on screwing it all together. The idea was to make it disassemble-able, but I changed my mind. Alternately, the Velcro could be replaced with double-sided 3M foam tape (though that wouldn't be thick enough to bridge the front gap between the two small drawers in the second picture.

20180330_165717.thumb.jpg.16cebef096b270a222d5316439775419.jpg

And now the final product, all stocked up! Esslinger's Watchmaker's Anti-Static Bench Mat Work Pad fit pretty darn well on the tray, with a little extra space around the edge to set things that might roll otherwise. The drawers have no locking mechanism, so make sure they don't slide open during transport. They do have some tabs to prevent them from falling all the way out, but that probably won't help much by that point. Final height is 7 13/16". The tray itself is textured, so a vacuum-clamp vise like the one in the blog post would likely not work.

20180330_171806.thumb.jpg.feb8fbdf294fb99239b3ea82208f455f.jpg

Hopefully folks find this useful. If you want, you could always stack more drawers. I find this size to be work pretty well and easy enough to store in the closet.

Kevin

  • Like 5
  • Thanks 1
Link to comment
Share on other sites

Excellent work, this is the beginning of a slippery slope, temporary workbench will become a permanent one later on - even if it means putting it in the toilet !

They tray is a good idea for when parts roll off, I remember using the whiteboard to actually make notes about the watch I was working on.

Glad you liked the blog post, forgot about that setup , that started everything for me !

Jonathan

Sent from my ONEPLUS A3003 using Tapatalk

Link to comment
Share on other sites

7 hours ago, jnash said:

Excellent work, this is the beginning of a slippery slope, temporary workbench will become a permanent one later on - even if it means putting it in the toilet !

They tray is a good idea for when parts roll off, I remember using the whiteboard to actually make notes about the watch I was working on.

Glad you liked the blog post, forgot about that setup , that started everything for me !

Jonathan

Sent from my ONEPLUS A3003 using Tapatalk
 

Thanks, Jonathan! I always appreciate a good DIY project, and yours was a very clever one that was just what I needed at the time!

Kevin

Link to comment
Share on other sites

  • 2 years later...

Great work. I like that it's modular and upgradeable. And when you move on to something better, it can be repurposed.

In case you are looking for some elbow/wrist support, I discovered these accessory from Aliexpress. 

The adjustable sofa legs and flexible led lights will be great additions for the future.

1039171307-1860805432.jpg

10295476181442482346.jpg

1049907434-323398818.jpg

Link to comment
Share on other sites

Great ideas for accessories!

Since building this portable workbench, I purchased a 46" Husky adjustable-height work table from Home Depot that I otherwise use to work from home. Managed to procure my grandfather's old Luxo L-1 lamp, and bought a clamp-on monitor holder to clear off some of the work surface.

I still use my portable workbench for its storage while I work on watch projects, so moving up was not completely moving on 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be.
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
×
×
  • Create New...