Jump to content

Modernising a Watch with Sentimental Value


Recommended Posts

4 minutes ago, jdm said:

Good intent and welcome, but before going at something of sentimental value I really recommend to that you practice first on something of no real value and about which you don't care about. It's very normal for beginners to make irremediable mistakes (I did many too) and underestimate the difficulty of tasks, as well the need for specific tools, etc.

I agree with what you are saying completely. I plan to only keep the case and back and replace everything else. I would have loved to put a mechanical movement in the watch but I think it’s too small (33.9mm x 7.1mm). 

My plan is to have the case and back replated and have the back blanked of its manufacturers engraving so as I can have a blank canvas to have something engraved on it myself. I was hoping to get advice on what movements could be used and buy the parts ready for a watchmaker to assemble as like you said, I don’t want to ruin the watch. 

I’ve already started sourcing/ordering parts which was a little silly without any advice so I’ll post what I have ordered below (if rules permit me to do so?). 

 

91FE7A54-EE7A-47D3-BF35-73CF944BBB93.jpeg

2B614C4F-BBFC-4B29-8B26-B42E675AB4B3.jpeg

Link to comment
Share on other sites

1 minute ago, ash.bez said:

I would have loved to put a mechanical movement in the watch but I think it’s too small (33.9mm x 7.1mm). 

That would have made it really another watch, not your grandfather one. You can do such swaps on other models, but normally is not practical  or worth the work.

1 minute ago, ash.bez said:

My plan is to have the case and back replated and have the back blanked of its manufacturers engraving so as I can have a blank canvas to have something engraved on it myself.

Case and back seems fine and will look good with a light polishing. You will find that replating is expensive and often does not lead to the desired results. If the mov.t works just leave it alone otherwise replace with a new Seiko one. As mentioned above my opinion is that objects kept as memories are best left just as owned by the missed person.

Link to comment
Share on other sites

Thanks again jdm. Unfortunately the gold plating on the case is in bad shape and has flaked off in numerous areas, the dial has corrosion around the edges and the movement has stopped working. I appreciate what you’re saying regarding changing the look of the watch but the watch was given to me to remember my grandfather with and I still feel that having the original case with an inscription on the back will do this plus it will get far more wrist time as it is currently just collecting dust. 

Link to comment
Share on other sites

Hi there,

this is my first post and I hope that I can tap some of your vast knowledge to help me with my labour of love project. 

I was given my grandfathers watch as a keepsake when he passed and although it is worthless in terms of monetary value it obviously has great sentimental value to me. 

I know many of you may disagree with my plans for the watch (keep the case and back and have replated and the case back ‘blanked’ ready for engraving and replace everything else) but it has just collected dust since I was given it. 

The case is in bad shape and the gold plating is flaking in numerous areas. The movement has stopped working and the dial has corrosion starting around the edges. 

My plan is to have the plating done myself and source all the relevant parts ready for a watchmaker to assemble. I have jumped the gun slightly and have started buying parts without advice (may turn out to be a silly move!). The parts I have bought are below;

D100 (29.2mm domed crystal) from watch-batteries.com

https://m.ebay.co.uk/itm/31-5-28-5mm-Bliger-Black-Dial-Ming-zhu-2813-3804-Miyota-82-Series-Movement-P576/262934969958

I was wondering if there are any hand wind movements that would fit the case? If I need to purchase a different face then so be it as I was a little hasty in purchasing this!

If there isn’t a mechanical movement that will fit I have been looking at the Ronda quartz movements (6003.D). Would these be compatible?

Sorry for the long winded post but I hope you can all help. 

Many thanks in advance, Ashley. imageproxy.php?img=&key=77f0dcc5ac0f9d5b

BDCE7532-CD04-4DBD-A901-7A2B10772F73.jpeg

2340A790-ED07-4E8F-9EB2-ED3F6A37D76B.jpeg

Link to comment
Share on other sites

22 minutes ago, ash.bez said:

I was given my grandfathers watch as a keepsake when he passed and although it is worthless in terms of monetary value it obviously has great sentimental value to me. 

I know many of you may disagree with my plans for the watch (keep the case and back and have replated and the case back ‘blanked’ ready for engraving and replace everything else) but it has just collected dust since I was given it. 

Most subjects already discussed at: https://www.watchrepairtalk.com/topic/8593-introducing-myself/
I would appreciate if you could keep the discussion into a single topic, and will merge the two, as you indicate into which section you prefer this to be.
 

Quote

If there isn’t a mechanical movement that will fit I have been looking at the Ronda quartz movements (6003.D). Would these be compatible?

No. Your watch has a Seiko V501 mov.t which can be replaced with an Y121, cost about $2. Anything else, quartz or mechanical will not fit.

 

Link to comment
Share on other sites

2 hours ago, jdm said:

Most subjects already discussed at: https://www.watchrepairtalk.com/topic/8593-introducing-myself/
I would appreciate if you could keep the discussion into a single topic, and will merge the two, as you indicate into which section you prefer this to be.
 

Thanks for the reply. It would probably be best left here if that’s ok as this post has more information. 

Link to comment
Share on other sites



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...