Jump to content

Frankie

frankie

By frankie
in Introduce Yourself Here

 Share

Recommended Posts

frankie New Member

frankie

Posted
Posted

Howzit! I live on a rural island in the middle of the Pacific Ocean and there are no watch repairmen here; the shops here send even the simplest jobs to Honolulu, about 250 airmiles from the island where I live. I don't have expensive watches but I wear a variety of watches and now I have 4 which are not working. So I went online to see if I could figure out how to repair them myself. Now I want the basic instruction of how to open my watches. Obviously, I'm not going to work on more than one at a time so I don't mix up the innards! I keep trying to start the basic lessons but can't find how to access them. I have already registered. Thnx, Frankie

Link to comment
Share on other sites
ecodec WRT Addict

ecodec

Posted
Posted

Hi Frankie, Welcome to this fine forum. Well, what can I say. You have to get fixing those watches for the Islanders !!. Help is here. I recommend Mark Lovicks videos, and a book that I have had for many years. Donald de Carles Practical Watch Repairing for practical and theoretical info:. All good wishes for your success. Kind regards, Mike.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Movement inserted from crytal side

      By oldhippy · Posted

      Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
×
×
  • Create New...