Jump to content

Hendomas 8 Day Pocket Watch Repair and Servicing


Recommended Posts

I’ve just watched your video right through. It is very awkward trying to clean a movement without a proper cleaning machine. The mainspring repair is ok providing the screw does not rub against the spring. What types of oil did you use? The action of the balance is very poor, what about the time keeping. With such a powerful m/spring, when it is run down that balance will hardly rotate. I would check the whole escapement for old oil and make sure the jewels are spotless. It would have been a good idea to have assembled the train and tested before putting in the pallets. Good luck.  

 

Are you going to video the up-date when sorting out the balance? I do hope so.

  • Like 1
Link to comment
Share on other sites

I’ve just watched your video right through. It is very awkward trying to clean a movement without a proper cleaning machine. The mainspring repair is ok providing the screw does not rub against the spring. What types of oil did you use? The action of the balance is very poor, what about the time keeping. With such a powerful m/spring, when it is run down that balance will hardly rotate. I would check the whole escapement for old oil and make sure the jewels are spotless. It would have been a good idea to have assembled the train and tested before putting in the pallets. Good luck.  

 
Are you going to video the up-date when sorting out the balance? I do hope so.

I did take the balance out and cleaned it in an ultrasonic cleaner while contained in a smaller container. I did clean the jewels and the hairspring is now perfect. Got it swinging 270 deg now. It does run too slow: ind i have the regulator cranked over to fast. I could undercut the balance screws or even remove two and see what happens. For now, i am satisfied that it actually ticks, Phase 2 will be timing...when i get the energy.9abca5c1d08c1ea5405fc7eb5117b70c.jpg


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

I wouldn’t play around with the timing screws just yet. The best and safest thing is to take the hairspring in and re-pin. You will have to change the position of the hairspring on the balance to get it in beat but that is not difficult.  

  • Like 1
Link to comment
Share on other sites

I wouldn’t play around with the timing screws just yet. The best and safest thing is to take the hairspring in and re-pin. You will have to change the position of the hairspring on the balance to get it in beat but that is not difficult.  


Ok, the problem was actually a loose cannon pinion. So what i did was use one of my wife’s hairs and carefully placed it inside the cannon pinion. Then i slide it back onto the pivot/arbor. This provided enough friction for the cannon pinion without having to tighten it the normal way. I was afraid of damaging the cannon pinion as i have no other hebdomas movements for parts. So my wifes dna is now part of the watch. Please don’t yell at me for using that technique. The swing is around 180deg.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites


Ok, the problem was actually a loose cannon pinion. So what i did was use one of my wife’s hairs and carefully placed it inside the cannon pinion. Then i slide it back onto the pivot/arbor. This provided enough friction for the cannon pinion without having to tighten it the normal way. I was afraid of damaging the cannon pinion as i have no other hebdomas movements for parts. So my wifes dna is now part of the watch. Please don’t yell at me for using that technique. The swing is around 180deg.


Sent from my iPhone using Tapatalk Pro

b016ac4b0559e5c0bb895f98142bcbf1.jpgaa64eaa400f224a33b048b998409a314.jpg862d10fdbb4a5094d46ae8ffa65868b0.jpg1708e1f31c570f684c6c1aade976fca9.jpg



Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites


Ok, the problem was actually a loose cannon pinion. So what i did was use one of my wife’s hairs and carefully placed it inside the cannon pinion. Then i slide it back onto the pivot/arbor. This provided enough friction for the cannon pinion without having to tighten it the normal way. I was afraid of damaging the cannon pinion as i have no other hebdomas movements for parts. So my wifes dna is now part of the watch. Please don’t yell at me for using that technique. The swing is around 180deg.


Sent from my iPhone using Tapatalk Pro

b016ac4b0559e5c0bb895f98142bcbf1.jpgaa64eaa400f224a33b048b998409a314.jpg862d10fdbb4a5094d46ae8ffa65868b0.jpg1708e1f31c570f684c6c1aade976fca9.jpg



Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

I’ve just watched your video right through. It is very awkward trying to clean a movement without a proper cleaning machine. The mainspring repair is ok providing the screw does not rub against the spring. What types of oil did you use? The action of the balance is very poor, what about the time keeping. With such a powerful m/spring, when it is run down that balance will hardly rotate. I would check the whole escapement for old oil and make sure the jewels are spotless. It would have been a good idea to have assembled the train and tested before putting in the pallets. Good luck.  

 
Are you going to video the up-date when sorting out the balance? I do hope so.

I actually did not show the cleaning, only putting a few small parts in lighter fluid. I actually hand clean each part, peg out all the jewels, sink the pinions in soft wood and shine all the pivots. I also toothpick the movement plates to get any corner gunk out. Did not tape that as it would have taken another hour. PS: I do listen to all your advice over the years, Big Thanks.

Sent from my GT-N5110 using Tapatalk

Link to comment
Share on other sites

I would have liked to have watched all that. Good luck.

The watch is now slow 5 min over the past 30 hours. Getting closer. Without a new “not set” mainspring, I don’t think i can get the amplitude any better.a0f71c197da5485aa203d1b626129191.jpg


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
    • Once a movement has the dial and hands put back and it is recased, would you expect the assembled watch to have the same amplitude as when the movement is in a movement holder and is without hands and dial? Thanks
    • C07641+ not sure what the "+" is for after the last digit.
×
×
  • Create New...