Jump to content

"Mistral" Ultrasonic clock cleaner review


clockboy

Recommended Posts

As promised I would give review of this ultrasonic clock cleaner also can be used for cleaning carburettors.

IMG_2227.thumb.jpg.3fc92e077599ba9770ff0ade24eb279d.jpg

Well it certainly cleans with remarkably good results. I cleaned a very dirty "Hermle" clock movement mixing this solution 7:1 in warm water. The parts come out of the cleaner spotless & shiny ,I rinsed with water and rinsed again with L&R rinse.
HOWEVER I was not aware that this solution has some sort of ammonia base and bearing in mind my workshop is a converted bedroom. The fumes were overpowering, windows opened doors shut & the wife was not happy to say the least. I will in the future have to use my garage when using this cleaner and perhaps apologise to the neighbours in advance. :mellow::mellow:

Conclusion: This cleaner gives excellent results and is very economical. However it must be used in a very well ventilated room. I recommend the wearing of a mask as well as the fumes are very strong indeed.  I will have to do some more research to find a good ultrasonic cleaner that I can use without the fumes. 

Link to comment
Share on other sites

Stardrops Floor-Cleaner....

Providing its just brass/steel, gilt, nickel etc, this works well, contains a small amount of ammonia and various ionic and non-ionic serfactants, with a little pine-oil.

Has sometimes the tendancy to 'blue' steel components or those coated with lacquer. Use in ultrasonic, a good squirt and at 50-80 degrees for 10 minutes.

Rinse well (4-5 times) then into Alc. and back in ultrasonic to de-water and dry.

 

Link to comment
Share on other sites

Hi All,

Try this one..

Product overview

• New double strength formula - increased effectiveness against tarnish!
• Ideal for use with or without an ultrasonic cleaner to return items to a shiny condition
• Assists in the removal of tarnish, carbon, rust and dirt from most metals to return items to a shiny condition
• Non-toxic, non flammable and bio-degradable
• Should only take a few minutes to clean when used with an ultrasonic cleaner
• Made from natural products; mixing seaweed, coconut oils and other fruit extracts to create a powerful cleaning solution
• Made in the UK

A76LG_1.jpg

Link to comment
Share on other sites

  • 2 months later...

Apologies for resurrecting an old topic.

I know Horolene is the de-facto cleaner - does this remove the tarnish as well?

I've been working on a Smiths Empire 151 that's had a run in with 3-in-1 or WWII tank engine oil and despite using my best efforts still seems to retains a slightly greasy patina. So are in the case of restoring an old clock, is the aim to remove this patina and reveal a clean bright surface, or just to remove the excess gunk and emulsified oil?

I have tried my "silkolene fuchs wash off" which is designed to shift motorcycle chain grease (which is designed not to be shifted) and even after 6 mins in the ultrasonic in that the plates don't feel clean!

Link to comment
Share on other sites

Yes, horolene will remove tarnish, as will any amoniated cleaner. I usually buy mine at the clock and watch fair at the motorcycle museum to save the postage hassles, but Cousins will ship it.

I’m sure there are many cleaning fluids which will give a good looking outcome, but I work on the basis that Horolene is not that expensive and being as it’s designed for the job will do what is required and not leave any nasty residues behind or do any unseen damage.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi. Sounds like a problem clock, can you post some picture# of the clock and the parts in question please.       Thank you
    • The first broke while i was using a dremel to shape the jumper spring at the join, i guess you call it the fixator, the disk grapped hold and flicked it off . The second time same place but while i was filing.  This steel feels more malleable, it is annealed steel. Working out the detent on the jumper is a real. pain in the butt.
    • I'm trying to get a balance spring Mantel clock to run to time - even with the regulator set to Slow it's gaining 40mins a day (the balance spring was damaged on receipt so it may be shorter than it should be - can't think why else it should run fast, especially as it is quite dirty & apparently hasn't been working for some time.). Anyway, looking closely at the train I've noticed the pre-escapement wheel is slightly 'dished'. Could this have been done by a previous tinkerer to get around a problem that should have been addressed by e.g. bushing pivot holes?
    • Hi Rich, now i realise that you spring broke. how did it broke, may be when grinding the fixator part with the dremel? If so, then guess You have let it to vibrate free, this is wrong. One must keep the spring pressed with finger to boost the vibrations, other vice it resonates and breaks.
    • The movement is so called 'Tongji', standard chinese movement. The stem can still be used with the help of extender.
×
×
  • Create New...