Jump to content

Reassembling gears

tucker810

By tucker810
in Watch Repairs Help & Advice

 Share

Recommended Posts

tucker810 New Member

tucker810

Posted
Posted

I just took apart my first working watch and I am having trouble with the three gears. Everything else is easy to reassemble but the three gears leading to the mainspring. How do you guys put them back together? I am new to this so any help would be greatly appreciated.

  • Confused 1
Link to comment
Share on other sites
mousekar Member

mousekar

Posted
Posted

If I understand you correctly, I believe you’re talking about the gear train? It takes some practice, a lot of patience and persistence. It can be done! Some are easier than others I have found.
I am only a hobbyist, so someone who is more trained then I am, may be able to offer better advice.
The technique that gets me the best results, is to very gently apply a small amount of pressure (just enough to keep it in place) either with peg wood, or with my finger while I hold the movement, and use my tweezers to individually move the gears in place. When all the pivots are in, the plate will fall into place. DO NOT push down, or you may bend a pivot! DO NOT force anything. These are delicate pieces of fine mechanics. Tolerances are very exact.
I’ve picked this up from watching a substantial amount of videos. So just watch videos of movements being assembled by people who know what they’re doing (there are a number by hobbyists, and while interesting are not as refined) and you’ll pick up a lot of proper techniques.
Hope that helps!
Cheers


Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
mousekar Member

mousekar

Posted
Posted

Edit: I meant to say “bridge”. Place the gears in the pivots correctly, place the “bridge” on top VERY gently and apply a small amount of gentle pressure with peg wood or finger on the bridge to keep it in place while you use your tweezers to adjust the gears to get the top pivots in the “bridge” (not plate).
I’ve also seen and done, putting the bridge in place and then putting in the bridge screws but NOT tightening them down (very important). You have to allow some play in the bridge so you can adjust the gears to get the pivots in. Either way, I would check out some videos first, see a pro like Mark Lovick do it a few times and then give it another go. If you get frustrated, walk away because you may try to force something at that point, and that’s when things go flying or break.
Good luck. You can do this! Hope this helps.


Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
tucker810 New Member

tucker810

Posted
  • Author
Posted
9 hours ago, mousekar said:

If I understand you correctly, I believe you’re talking about the gear train? It takes some practice, a lot of patience and persistence. It can be done! Some are easier than others I have found.
I am only a hobbyist, so someone who is more trained then I am, may be able to offer better advice.
The technique that gets me the best results, is to very gently apply a small amount of pressure (just enough to keep it in place) either with peg wood, or with my finger while I hold the movement, and use my tweezers to individually move the gears in place. When all the pivots are in, the plate will fall into place. DO NOT push down, or you may bend a pivot! DO NOT force anything. These are delicate pieces of fine mechanics. Tolerances are very exact.
I’ve picked this up from watching a substantial amount of videos. So just watch videos of movements being assembled by people who know what they’re doing (there are a number by hobbyists, and while interesting are not as refined) and you’ll pick up a lot of proper techniques.
Hope that helps!
Cheers


Sent from my iPhone using Tapatalk

This is really helpful! Thanks, can you recommend any good videos?

Link to comment
Share on other sites
  • 1 month later...
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      I dont understand why a patreon membership would have limited places ??
    • clockboy
      Hi all

      By clockboy · Posted

      Welcome to the forum, enjoy. It’s highly unlikely you will be able to purchase a new bezel look on eBay for a pulsar watch for repair to find a bezel.
    • JohnR725
      Balance spring fell out of regulator pin.

      By JohnR725 · Posted

      just one little minor reminder here this isn't your normal balance wheel.  pages 17 and 18 are what you really want to be looking at. normally studs don't turn but this watch has the etachron system designed for lots of adjustment. Personally I would try to rotate the stud back to where it's supposed to be. If you're lucky you didn't actually bend it at the stud it just looks really bad as the stud has been rotated grossly out of position.. I think things will look a lot better if you put the hairspring back where it's supposed to be by rotating the stud. it's hard to tell if you actually did bend it at the stud or not we won't know until you rotate the stud back more or less where it's supposed to be. Then you want to pay attention to the manual of how to put the hairspring back in the regulator pins because yes they rotate also and they rotated specific directions otherwise bad things will happen to your hairspring. so initially you can open up the regulator as wide as it can go and don't worry about closing it until thing everything is right then you can close them a little bit
    • oldhippy
      Is this a 'hack' ?

      By oldhippy · Posted

      I need to see photos of the whole movement before I comment. 
    • swiss2k
      Omega cal. 565 - low amplitude

      By swiss2k · Posted

      Hi @Jon, so, from one extreme to another the beat error is 0.1(min.pos) to 0.2(msx.pos), and as you mentioned the rate does up and down dramatically. Also checked the position of the collet, and the collet is not central to the jewel on the balance cock. Balance moves freely, per my understanding.   So, after 24h the ampl. fell down by approx 20 deg, which I would assume is expected. After adjusting the endshake I believe I gained around +10 deg. of balance movement. Which is great, and overall the balance is not at 220'ish deg.   What I did next, some might think is non-orthodox, but was wort a try. I too the mainspring out, checked again for endshake and if the pin moves freely, and cleaned everything. Usually when installing the mainspring I would use some barrel grease on the barrel walls, install the spring and put a 2-3 drops of D-5 oil on top of the wounded spring and in the places where the arbor sits. This time I took the spring and applied a ultra this coat of Molykote Dx paste on the whole spring, before installing it in to the barrel, and added some oil to the arbor as usual.  The result improved, at a full wound the balance produces about 230-237 deg. @JohnR725 I'm getting closer to 300 😃   What I am noticing, there is a fluctuation in amplitude. With time it would rise and drop about total 8-10 deg in an interval about 2 minutes. I assumed this ruled out the power transfer from the barrel itself. So I took the gear train out, cleaned and lubed. 
×
×
  • Create New...