Jump to content

Reassmble Problems - Newbie needs advice

Link

By Link
in Watch Repairs Help & Advice

 Share

Recommended Posts

Link Member

Link

Posted
Posted

All things considered, my first tear down and rebuild didn't go too bad.

Some general things I learned:

  • Face side first!
  • Don't grab things too tight with the tweezers, two screws are somewhere on the floor
  • Don't over tighten screws, I broke one off and somehow managed to get it out
  • Take photos, don't rely on an exploded diagram

Ok so my questions. Here is the movement tech sheet I was using.

Crown set bridge. The crown locked in place but it wouldn't engage any gears. Any clue what went wrong? I'm assuming what they call the sliding pinion is in the wrong location or I'm missing tension on it? I just can't tell from the diagram what I did wrong. Photo as I assembled it:

IMG_0129.thumb.JPG.462b6299f488c660c794a894dba6bbbd.JPG

The balance wouldn't freely spin after assembly. My assumption here is the staff didn't make contact with the top and bottom pivots? Should I have taken off the regulator to seat that jewel correctly? Did I mess up the staff? Two photos:

IMG_0133.thumb.JPG.df23ca560341210c77520f3169fb37db.JPGIMG_0130.thumb.JPG.38345e954a8ad9ebe3dcc0630b8cbc51.JPG

 

The gear above the crown with the huge flat head screw. I assume this isn't made to come off?

 

IMG_0131.thumb.JPG.a573b0082724545093b4ac2dcf813316.JPG

 

Link to comment
Share on other sites
anilv Distinguished Member

anilv

Posted
Posted

re crown set bridge - the set lever should hold the winding pinion against the clutch wheel.. ie the two parts with the ramped teeth should be forced together when the set lever and its spring is installed.

A pic without the bridge would assist diagnosis.

Balance wheel. Can only see one pivot clearly.. the other should look the same. You would usually get the balance in place and the balance bridge in position before tightening everything down gradually while making sure the balance spins. Tightening the screw in one go will break the pinion if it is not safely in its hole. If the balance spins one way and not the other then the impulse jewel is not in the fork at the end off the pallet lever. If all is in place correctly but the balance is still sluggish then you may need to clean the balance jewels again.

big screw/gear .. this is usually a left handed screw. ie clockwise to open. It is also usually very tight. This can break, especially if someone has already used force to try and unloosen it like a normal screw. I would leave it alone for the moment

good luck!

Anilv

  • Like 1
Link to comment
Share on other sites
Link Member

Link

Posted
  • Author
Posted


big screw/gear .. this is usually a left handed screw. ie clockwise to open. It is also usually very tight. This can break, especially if someone has already used force to try and unloosen it like a normal screw. I would leave it alone for the moment
good luck!
Anilv


Ah! It spins freely now but doesn’t come out. I guess I broke it.

Thanks for the help!



Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
anilv Distinguished Member

anilv

Posted
Posted
2 hours ago, Link said:


big screw/gear .. this is usually a left handed screw. ie clockwise to open. It is also usually very tight. This can break, especially if someone has already used force to try and unloosen it like a normal screw. I would leave it alone for the moment
good luck!
Anilv


Ah! It spins freely now but doesn’t come out. I guess I broke it.

Thanks for the help!



Sent from my iPhone using Tapatalk

Ouch... well live and learn.

It is good when working on unfamiliar movements to check on the direction a wheel/gear will rotate when in use.

In this case, when the watch is wound, the gear would move counter-clockwise and potentially this could cause a normal screw to unscrew, hence the use of a left-handed thread which will only get tighter.

Most manufacturers will mark the head of a screw with 3 lines to indicated that it is a left-handed thread but there will be some exceptions.

Anilv

 

Link to comment
Share on other sites
rappeleur Member

rappeleur

Posted
Posted (edited)

It looks like the pallet fork is not in the right place... It is not evenly lying / rather slanted. Is it moving freely from left to right and vice versa? (maybe it is just the angle of the photo).

Capture+_2018-03-13-23-35-32.png

Edited by rappeleur
Inserted detail pic
Link to comment
Share on other sites
hokavan Watch Enthusiast

hokavan

Posted
Posted
It looks like the pallet fork is not in the right place... It is not evenly lying / rather slanted. Is it moving freely from left to right and vice versa? (maybe it is just the angle of the photo).
5aa852a1a7c30_Capture_2018-03-13-23-35-32.thumb.png.8fa62f57f42e57bce8b8e3217786e393.png

The pallet fork moves with each rotation of the escape wheel. With photo can not judge if it is evenly lying or not. However you can check yourself by gently notch the fork from both directions. If it moves with escape wheel it seems to be okay. Remind that you should check the pivot of the pallet fork before tightening the screws.


Sent from my iPad using Tapatalk
Link to comment
Share on other sites
rappeleur Member

rappeleur

Posted
Posted

yeah, I know, I wanted to give adive to the TO "Link"  for his/her problem:

On 13.3.2018 at 1:01 AM, Link said:

The balance wouldn't freely spin after assembly

I only saw the photo and thought this might be a thing to check for him/her before taking apart the whole movement... (It may also be that the balance was just set a bit wrong in place, so that the jewel came to lie outside the pallet fork and thus couldn’t be moved by it).

 

 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
7 hours ago, hokavan said:

With photo can not judge if it is evenly lying or not.

For sure the pallet can't stay in the middle like that. Definitely something is wrong with that escapement.

Link to comment
Share on other sites
Link Member

Link

Posted
  • Author
Posted (edited)

Thanks everyone for the advice!

I think I had the pallet installed incorrectly, I was able to wind it up slightly and make the escapement tick after this try. As far as I can see in my loupe the pallet isn't damaged. For the balance, it has a tooth looking jewel, impulse jewel? where should I put this during installation? In the fork? Should the spring have any tension?

IMG_0139.thumb.JPG.b8b54ecb5371a3b2138dd22f968139d9.JPG

Now on to the crown. Here is a pic with the set bridge removed. What is wrong with this picture? I feel like the spring isn't in the right place. Actually I think maybe the sliding pinion is backwards?

These pics are all through a 10X loupe and my iphone, this works amazingly well.

IMG_0140.thumb.JPG.2a4ae41c35ac07a919dad5096fec43dd.JPG

Edited by Link
I can't spell
Link to comment
Share on other sites
Eckehardt Watch Enthusiast

Eckehardt

Posted
Posted

The roller jewel on the escape wheel should rest between the banking pins ( no tension). This can be checked with the pallet fork removed and the balance cock reinstalled. And looking between the banking pins make sure the roller jewel on the balance wheel roller table is perfectly between those pins.

Link to comment
Share on other sites
Eckehardt Watch Enthusiast

Eckehardt

Posted
Posted
9 minutes ago, Eckehardt said:

The roller jewel on the escape wheel should rest between the banking pins ( no tension). This can be checked with the pallet fork removed and the balance cock reinstalled. And looking between the banking pins make sure the roller jewel on the balance wheel roller table is perfectly between those pins.

 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      I did not. I thought about it, but I had cleaned it in my ultrasonic, and the tech sheet shows lubricating it in place already assembled, so I figured discretion was the better part of valor. Although since I have to depth the jewels anyway, maybe I pull the pinion off to rule it out 100% as part of the problem. Do you know if there's a safe way to do it? I don't want to use a puller because it would push down on the plane of the wheel, and that seems like a Bad Idea. I thought about using a roller table remover, but I don't think I have a hole stake pointy enough to push it down.
×
×
  • Create New...