Jump to content

Economical watch tools (again)


oldhippy

Recommended Posts

7 minutes ago, oldhippy said:

When it comes to horological tools the trade is flooded with foreign imports of inferior quality.

No doubt but since there are economical tools which do their job perfectly, our duty is to inform about these. No generalizations please.

Link to comment
Share on other sites

I recommend to members on here of the type of tools I have used which I think is justified. I am not going to advise people of tools I have never used. Watchmakers/repairers on other forums, do not recommend cheap imports.   

Link to comment
Share on other sites

39 minutes ago, oldhippy said:

I recommend to members on here of the type of tools I have used which I think is justified. I am not going to advise people of tools I have never used.

Absolutely, see all my postings mention type and purchase place of the tools that I use.

Link to comment
Share on other sites

On 16-3-2018 at 2:15 AM, Deggsie said:

Is there a chat section entitled "Freedom of Speech In the Western World" and one about "Why I fought For my Country's Ideals"?  Meant light heartedly JDM, but we are only "chatting".

jdm just pointed out to discuss it in the correct section,...I agree with him...keeping it on topic

  • Thanks 1
Link to comment
Share on other sites

I have many Chinese and foreign tools. Cheap and cheerful screwdrivers, Tweezers, movement holders etc. All re-engineered by myself and all are very good at little cost. If the tools are prepared correctly for the work then the rest  is mainly down to the skill and know how of the repairer. Just my opinion. It is my understanding that a lot of Chinese manufactured components are used by a large movement maker and it is not unknown nowadays for expensive watches to be 1st. class air mail insured and shipped to China for service/repair if one knows where to go in China for this work. The sender then triples the cost to his customer. 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

On ‎3‎/‎13‎/‎2018 at 6:46 AM, rodabod said:

Just remembered: I bought a Chinese Katsu Mini Pillar Drill recently and it’s incredibly good. Virtually no play, and a very clever design using a sewing machine motor. 

Interested in info on this please...

Link to comment
Share on other sites

On topic:

I have a (Chinese?) crystal press. I used it as such once- it is fine but the dies, with their brass inserts, are worth less than dental floss at a Willie Nelson concert. The brass works loose and scored the crystal.

I have re-purposed it however. Using the correct dies, it is the absolute best way to remove (Aluminum) inserts from Rolex bezels without inflicting any damage to the inserts. It's also good at reinstalling them. Rolex crystals don't really need a press- only the crystal retaining ring. Formerly I have used a 12-point socket and a drill press to set them. However, I plan to make a dedicated tool, with the exact angle of the retainer, to set them properly. (it's on the list!)

I also have (knockoff) Rolex case back sockets which work very well. "Ruihua" brand, with a hand-wheel wrench. They will fit the "fancy" press tools but I have only one caseback that I can't remove with this tool. It's a Titanium case with a Titanium back. REALLY stupid since Titanium LOVES to gall and I think that's exactly what happened (or it's cross-threaded but back it sitting flush). It should have a stainless back. Anyway, that will be getting a liquid oxygen bath to shrink the back away from the mid case and it WILL come off...

I think I have some knock-off plastic tweezers too. Those are fine for holding a battery. The "Faux" Dumont tweezers are absolute garbage however. I have one pair I was burned on and they would not even make a good clothespin...

  • Like 1
Link to comment
Share on other sites

On 6/4/2018 at 10:21 AM, oldhippy said:

 

I recommend to members on here of the type of tools I have used which I think is justified. I am not going to advise people of tools I have never used. Watchmakers/repairers on other forums, do not recommend cheap imports.   

Very sound advice but I bought a small expensive screwdriver that was right out of line two years ago and have seen "experts" using similar ones on video  that wobble around, would not do for me.  Many tools have to be re-engineered in my humble opinion.

Link to comment
Share on other sites

9 hours ago, ecodec said:

Many tools have to be re-engineered in my humble opinion.

Some only. For example my Anchor drivers are fine, so are the Vetus tweezers. But the bench type case opener needed a little bit of work to clean some screws. So all cases are different, but on both I got noo big names, small cost, excellent performance.

Link to comment
Share on other sites

1 hour ago, jdm said:

Some only. For example my Anchor drivers are fine, so are the Vetus tweezers. But the bench type case opener needed a little bit of work to clean some screws. So all cases are different, but on both I got noo big names, small cost, excellent performance.

Me too and all agreed.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • that band is old as stated, there is a kit that pops up from time to time on selling sites for the repair of these type bands, some of this type are adjustable on a few links, one adjustable type allows you to align the round opening in the expansion slit [like yours] with the rivet to separate, but if yours won't come out then the rivet head is too big and will have to be done with some rivet removal and replacement, I suppose if you could make/optain the correct rivets that one could alter the said band, the tops/caps do lift off after raising the tabs....  
    • This is a watch from a friend who sent it to a neighborhood watchmaker for a battery change. It came back with the watch stem in a ziplock bag and the dial skewed 20°. The watchmaker told him that the stem was faulty and the watch cannot be repaired. I opened up the watch and found that one dial foot was broken off and still stuck in the movement, while the other was bent until it was flat against the dial. The stem could be inserted but it couldn't be pulled out to quickset and time adjusting positions. I did a full disassemble, cleaned and oiled the movement. But when it put in the battery, the second hand runs super fast. Like it gains 30 mins every hour. Any advice on fixing this problem? TIA.
    • I determined that the balance staff is rotating, not the roller table, so my second attempt at riveting was unsuccessful. I have ordered a new balance staff and will take measurements when it arrives. The balance staff i originally ordered (and now reordered) was specified as: Replacement balance staff: (A. Schild Caliber 984 1002 1021 1124 Original Balance Staff Part 723) so it should be correct. Measurements: (see pic below for terminology) xxxyy is a place holder until the new balance staff arrives. Lower pivot: Old - .08 mm New - xxxyy Lower pivot to balance seat: Old - 1.53 mm New - xxxyy Roller shoulder: Old - .42 mm New - xxxyy Hub: Old - xxxyy New - xxxyy Balance shoulder: Old - .86 mm New - xxxyy Collet shoulder: Old - .56 mm New - xxxyy Upper pivot: Old - broken New - xxxyy
    • Hello and welcome from Leeds.  We're here to help. 
    • I was just about to adk that, probably they have unnecessary waiting lists to make their watches appear more exclusive than they actually are.
×
×
  • Create New...