Jump to content

Schild and Cie Hebdomas 8 day pocket watch 6 jewel


Eckehardt

Recommended Posts

I have a Schild cie hebdomas pocket watch. Can anyone tell me what year era might this be. The only serial number I have is above the Schild Co is BW388SG. On the fold open caseback. Did they still use the the bridge type Balance bridge movement with the balance wheel in the center of the bridge like the open face dial version of the cie hebdomas style. Now for service. This unit has a huge mainspring with a special tooled holddown in the center. If one needs to remove that after the spring tension is relaxed. Does the center screw turn clockwise to open or counter clockwise? 

1515813446886801831142.jpg

1515813543412985485679.jpg

Link to comment
Share on other sites

I think your travel clock would date from around 1920 give or take 5 years either way, I dont think this movement has the same bridge layout as the classic open face Hebdomas it will have a fairly standard bridge layout with the regulator arm pointing downwards at a 90 degree angle please see this link to a watch it is a movement that will be similar to what is in this clock:

//www.ebay.co.uk/itm/Superb-8-day-w-w-1-1915-officers-silver-miltary-trench-wrist-watch-very-accurate/152857305233?hash=item2397016091:g:q68AAOSw-U1aUmOk

I have one of the watch versions of this movement but it is not in running order the teeth on the mainspring barrel are very delicate and are easy to break which is the case with the watch I have so for now it languishes in the parts bin, but I feel pretty sure the travel clock you have show will be a similar movement.

The screw in the center should unscrew in the opposite direction to the winding direction but either way as long as you are careful you should be able the get it off and be careful lifting the mainspring barrel off 8 days worth of mainspring goes a long way !

Link to comment
Share on other sites

This would around 1920’s to 1930’s going by the style of the case. Depending on the spring, this could be 30 hour or 8day. I cannot remember about the screw sorry. Just make sure you release all the power before attempting to take it apart. In many of these types of movements, the winding gears are prone to wear and slip, all down to the very strong spring in the 8-day ones, due to poor quality metal used in the winding meconium.  

Link to comment
Share on other sites

Was the Schild company or Otto Schild any relationship to the Legendary Adolf Schild the founder of Eterna. Or was this a total different Schild. It seemed like after Graizly turned over to Schild with Hebdow. It seems like the Schild end paled to insignificance. Too bad not more is written about this Company. Now Hebdomas end of it is totally different.

Link to comment
Share on other sites

  • 1 month later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Sounds great! And yes, I would use grease for the keyless as well although treating the parts with epilame would make the grease less likely to spread in the long run. Not critical but won’t hurt. My current strategy is to epilame treat all parts getting in contact with oil or grease.
    • Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.       I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • Hello and welcome from Leeds, England. 
    • Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
×
×
  • Create New...