Jump to content
  • 0
mikepilk

Balance staff for Smiths Cal 0104

Question

Can anyone help me with the part number for a balance staff for a Smiths Cal 0104 ?

Cousins just have : Balance Staff 723 (Generic) Smiths EA31

obsoletewatchandclockparts has a selection of Smiths balance staffs, but I don't know if any one is suitable

(He's also got a complete balance for a reasonable price .... may be the best option)

Thanks

Mike

Share this post


Link to post
Share on other sites

2 answers to this question

Recommended Posts

  • 0
25 minutes ago, wls1971 said:

The smiths part number for a staff was 01252/02 for the calibre 0104

this link will give you a view of the smiths technical documents for this calibre:

http://www.mwrforum.net/forums/showthread.php?76180-Smiths-Watches-A-Beginner-s-Guide/page2

Thanks for the info wls1971 . The technical docs are posted by John at obsoletewatchandclockparts , I've emailed him.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Answer this question...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • Awww. Mine are definitely much better JDR. . To be honest I don’t know, but that’s certainly an enviable display of screwdrivers. The grips aside, the main improvement I found was the precision ground stainless steel blade. Nice display box! Sent from my iPhone using Tapatalk
    • Isopropanol will soften and wash away the shellac. Take care with the balance and pallet fork. Just a quick dip of a few seconds, then straight onto watch paper to take off the excess, then use a puffer to dry the critical areas where the shellac bonds on the jewels. After 4 years using lighter fluid and thinking I was getting parts clean, I now use Elma watch cleaning product. Amazing how I fooled myself about how clean was clean. Also, try an ultrasonic which are very cheap nowadays. In general, IPA (isopropyl alcohol)is not a good cleaner, but is good for the final fine rinse if done quickly. Sent from my iPhone using Tapatalk
    • In order to properly service the movement you absolutely should remove the wheel so that you can clean any contaminated or degraded oil away (which if left could very easily result in premature wear and failure even if the side shake is acceptable now) and relubricate with fresh oil.  A dedicated 5 spoke wheel puller is the best way to go as it pulls at the hub, eliminating the risk of deforming the wheel, but not the only way. The important thing is to pull the wheel straight up with no twisting or canting of the wheel since the arbor is brittle and will snap sooner than bend. This can be achieved using two thin blades worked under the wheel from opposite sides to gradually wedge the wheel up. You may need to protect the bridge with some paper or tape to prevent scratches, and you need to use blades that are only very slightly thicker than the gap between the wheel and the bridge because you need to progress slowly, and don't be tempted to twist the blades. As long as the force is straight up in line with the arbor, and gradual enough to not deform the wheel, you should be alright. 
    • Discharge barrel power, then feel the side shake on the wheel( independently driven minute wheel), if no excessive side shake or other faults, just leave the wheel where it is, do not remove it.       
    • To safely remove you need a "5 Spoke Wheel Remover", check your materials house. 
×
×
  • Create New...