Jump to content

Refitting back cover after battery change

Eamonn

By Eamonn
in Watch Repairs Help & Advice

 Share

Recommended Posts

Eamonn New Member

Eamonn

Posted
Posted

Lorus watch  VX43 X092

prised off back cover without difficulty, fitted new battery but cannot replace cover. I notice depression on cover lip which seems to accommodate winder. Also an lip (about 2cm) protruding from cover lip. But no luck in refitting cover . (I did not need to twist cover to take off. I just put v thin flat driver under the protruding lip and it detached)

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted
Lorus watch  VX43 X092
prised off back cover without difficulty, fitted new battery but cannot replace cover. I notice depression on cover lip which seems to accommodate winder. Also an lip (about 2cm) protruding from cover lip. But no luck in refitting cover . (I did not need to twist cover to take off. I just put v thin flat driver under the protruding lip and it detached)

I still have a cover that will not snap back on. Tried every type of press.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

The reason why certain snap backs can't be closed by hand is that the pressure must be uniform on the entire edge, not on the center. One can try improvising shaping two pieces of wood as dies in  a vice, but be careful, it is a matter of precision, not force.

 

  • Like 2
Link to comment
Share on other sites
PJA WRT Addict

PJA

Posted
Posted (edited)

Watch this video. I'm not sure whether it's the best available or not but it'll give you some sort of idea. from a bad experience, I suggest you don't try pressing too hard with no tool because you'll end up with a broken glass. In any case, the tool is less than $14 and well worth it and so much cheaper than going to a jeweler.

Edited by PJA
Link to comment
Share on other sites
Eamonn New Member

Eamonn

Posted
  • Author
Posted

I got the rear cover refitted using the press tool. I went to my jeweller who did it for me, exactly as in the Video above. Thanks for all the advice on this issue. Hopefully anyone who has a problem refitting the cover will read this post and know that the best and safest, and perhaps the only, remedy is the press tool. 

Thanks to all for your advice and help. It prevented me, among other things, from breaking the watch glass, and pointed me in the only sane direction. 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
4 minutes ago, Eamonn said:

In addition, is there any way of awarding points or completing this post so that those who contributed may be acknowledged.

On any posting, upvote is on the top left, like and other feedback types on the lower right.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Ok thanks Ross, I will give that a try!😁
    • rossjackson01
      Intro

      By rossjackson01 · Posted

      Welcome my friend. 
    • rossjackson01
      Help please.

      By rossjackson01 · Posted

      Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
×
×
  • Create New...