Jump to content

Refitting back cover after battery change

Eamonn

By Eamonn
in Watch Repairs Help & Advice

 Share

Recommended Posts

Eamonn New Member

Eamonn

Posted
Posted

Lorus watch  VX43 X092

prised off back cover without difficulty, fitted new battery but cannot replace cover. I notice depression on cover lip which seems to accommodate winder. Also an lip (about 2cm) protruding from cover lip. But no luck in refitting cover . (I did not need to twist cover to take off. I just put v thin flat driver under the protruding lip and it detached)

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted
Lorus watch  VX43 X092
prised off back cover without difficulty, fitted new battery but cannot replace cover. I notice depression on cover lip which seems to accommodate winder. Also an lip (about 2cm) protruding from cover lip. But no luck in refitting cover . (I did not need to twist cover to take off. I just put v thin flat driver under the protruding lip and it detached)

I still have a cover that will not snap back on. Tried every type of press.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

The reason why certain snap backs can't be closed by hand is that the pressure must be uniform on the entire edge, not on the center. One can try improvising shaping two pieces of wood as dies in  a vice, but be careful, it is a matter of precision, not force.

 

  • Like 2
Link to comment
Share on other sites
PJA WRT Addict

PJA

Posted
Posted (edited)

Watch this video. I'm not sure whether it's the best available or not but it'll give you some sort of idea. from a bad experience, I suggest you don't try pressing too hard with no tool because you'll end up with a broken glass. In any case, the tool is less than $14 and well worth it and so much cheaper than going to a jeweler.

Edited by PJA
Link to comment
Share on other sites
Eamonn New Member

Eamonn

Posted
  • Author
Posted

I got the rear cover refitted using the press tool. I went to my jeweller who did it for me, exactly as in the Video above. Thanks for all the advice on this issue. Hopefully anyone who has a problem refitting the cover will read this post and know that the best and safest, and perhaps the only, remedy is the press tool. 

Thanks to all for your advice and help. It prevented me, among other things, from breaking the watch glass, and pointed me in the only sane direction. 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
4 minutes ago, Eamonn said:

In addition, is there any way of awarding points or completing this post so that those who contributed may be acknowledged.

On any posting, upvote is on the top left, like and other feedback types on the lower right.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Oh nice. I have a similar wedge style stump for my staking tool, so I'll give that a shot. Thanks!
    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
×
×
  • Create New...