Jump to content

Disassemble for Repair: Henry Peck 1890 Pocket Watch

jdrichard
 Share

Recommended Posts

clockboy Distinguished Member

clockboy

Posted
Posted

JD good of you to post a vid uncensored. I found myself shouting at the vid :D

How that cannon pinion came off without any residual damage is a miracle. I suggest you purchase a nice cannon pinion removing tool. However should be a real nice watch when finished.

  • Like 3
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
JD good of you to post a vid uncensored. I found myself shouting at the vid [emoji3]
How that cannon pinion came off without any residual damage is a miracle. I suggest you purchase a nice cannon pinion removing tool. However should be a real nice watch when finished.

I had absolutely no patience on Sunday and had to beat the thing up. There is really no indent to grab the cannon pinion: just a pipe. So not sure a tool would work. I don’t treat any of the other watches this way:)


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I suffered a breakdown watching this.[emoji3] What a very lucky guy you were in not wrecking this movement.
For my health and sanity, I will skip part two.

clockboy I was doing the same[emoji3]


I knew that it was my most unprofessional moment: especially when the works dropped out while pounding the cannon pinion. I promise i will be a better professional with the second half. I was up till 3am the night before at my company Christmas party, and pooped. Nobody ain’t learning notten from this video. :)


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I bet the other Peck is s******g itself !!!!! LOL   I thought you were going to reach for a tyre lever. 

That is a funny reply. The other peck didn’t have the same cannon pinion issue and therefore was treated with kit gloves


Sent from my iPhone using Tapatalk Pro
  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
Hi JD, I have had many disasters and expect many more. I am a novice and have messed up a few watches because my skills didn't match my enthusiasm. Best regards Johnnie

So far i have no messups and about 70 pocket watch cleanings and repairs. I have also made 2 balance staffs: one works perfectly and one is awaiting reassembly. I have also cleaned quit a few watches including repairing a seiko Pogue chono. I have also pressed in jewels and trued balance wheels. So i have done a lot in the 3 plus years i have been studying and performing watch repair. I would also consider myself an amateur but have not screwed up a single watch. This one simply dropped from lack of focus on my part: could have been the first screwup but the watch gods protected me:)


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

If you are an amateur or hobbyist be in the right frame of mind to undertake the task. People that make a living out of horology have to knuckle down and get on with it. One thing that helped me was to get up and walk around or undertake a different repair and this time of the year make sure the workshop was nice and warm.  

  • Like 2
Link to comment
Share on other sites
Johnnie Super WRT Addict

Johnnie

Posted
Posted
1 hour ago, oldhippy said:

If you are an amateur or hobbyist be in the right frame of mind to undertake the task. People that make a living out of horology have to knuckle down and get on with it. One thing that helped me was to get up and walk around or undertake a different repair and this time of the year make sure the workshop was nice and warm.  

 

The above is a lesson I have learnt, when I am struggling and frustrated I now leave it and have a cup of tea! When I go back to it things seem to fall into place. 

  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted

Update: so i cleaned the watch completely and replaced the mainspring with one that i had. Had to anneal the end and bend in over to catch the barrel hook.

I then examined the jewels and found one badly damaged jewel and two other cracked jewels (fix later). Then i noticed that a tooth on the center wheel was bent completely over. I wedged in a knife and was able to move the tooth back without breaking. Lots of work remaining on this old beast. ace756c4ee1d35edc733399da85ef60b.jpg2b82ba18c9b05932b34e98abdd83b778.jpg28582a65b02988990c01113aa38527b7.jpgace602ee70c175eabfde5ca0153267f8.jpgbdf2a66be48b2bd405786b458e12b299.jpg430ddb57fb199fa80f83c06eac2f08f0.jpg


Sent from my iPhone using Tapatalk Pro

  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I suffered a breakdown watching this.[emoji3] What a very lucky guy you were in not wrecking this movement.
For my health and sanity, I will skip part two.

clockboy I was doing the same[emoji3]


BTW, I did manage to anneal an Elgin mainspring and fold the end over and and fit it into the Peck mainspring barrel. This was my first true mainspring mod work. Used an alcohol lamp and pliers. And I was very careful. I'm a bit pissed at the number broken jewels in this movement, but it is 1890 vintage

Sent from my GT-N5110 using Tapatalk

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Oh nice. I have a similar wedge style stump for my staking tool, so I'll give that a shot. Thanks!
    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
×
×
  • Create New...