Jump to content

My First Balance Staff - Need some advive


Recommended Posts

I just completed cutting my first balance staff on a lathe. All went well on the balance/hairspring side, including undercutting and leaving enough material to make the rivet. On the roller table side however, i cut a smidgen too much. Is there any way to tighten the roller table on or di i need to cut a new staff? I thought shellac on the post would harden and keep the table on. I still need to jacott the pivots, so am i waisting my time?

a661fc5f83101f0c50e6545520c5acf2.jpg9448f018ba52bc5ef968bc5b4f4572b9.jpg3c3e89d6b4af556e1689c44da6b6107a.jpg1fa364090bf8573a1573fe5b75db3049.jpga4dc217c5419d43dca0d97c40c1efb15.jpg26d4ecb70462e727ae771970d2d81a9e.jpgb2350b43733b2e39b0354d80d4f46aa5.jpg5b4c9e301b8ee136310fa056540830ed.jpg3aa5394b4d32b37db8f3cc63b55a2a67.jpg6b9c2d27bd3c565309c52db146a43f28.jpg

 

 

Sent from my iPhone using Tapatalk Pro

  • Like 5
Link to comment
Share on other sites

I just completed cutting my first balance staff on a lathe. All went well on the balance/hairspring side, including undercutting and leaving enough material to make the rivet. On the roller table side however, i cut a smidgen too much. Is there any way to tighten the roller table on or di i need to cut a new staff? I thought shellac on the post would harden and keep the table on. I still need to jacott the pivots, so am i waisting my time?
a661fc5f83101f0c50e6545520c5acf2.jpg&key=b63cfe8f836ff14588d3c1c5f13600455fa785f06c37f0c09647ab1e1c649c4b9448f018ba52bc5ef968bc5b4f4572b9.jpg&key=a150f0a233c327a68af670bb2cab24a85616bb20889a849a9c04e63f9794eaf13c3e89d6b4af556e1689c44da6b6107a.jpg&key=429ae1a5f0fa40a6eae5074b62565652e2e68ed4b84e84fa6bf4e9ac7577b0131fa364090bf8573a1573fe5b75db3049.jpg&key=4afb3571344584787b4c366efb07ac9f7704f5efbb9f37274e08c1d06a5749eea4dc217c5419d43dca0d97c40c1efb15.jpg&key=3d8c789ab151e06eac6e3d3e87d87c931ccade8993c72f9679c58c09ac46fd3326d4ecb70462e727ae771970d2d81a9e.jpg&key=becc5cd55829a6f37fe357ecef8f6529bc405976072628b86c948936a8f5cb5bb2350b43733b2e39b0354d80d4f46aa5.jpg&key=57c0ea5c34d285f72ebb03f87e472c7bc90d6407fcb6c3a4b8a0a3fbfc0aa46f5b4c9e301b8ee136310fa056540830ed.jpg&key=e2be288fe7c1abecd4f750c87b875a430eeff3b837579a7a603d8d7151987dbc3aa5394b4d32b37db8f3cc63b55a2a67.jpg&key=98fde1ccf489a7287489bf7be057875e66544264ac70259f3f4ef4b5c3fa8be16b9c2d27bd3c565309c52db146a43f28.jpg&key=6aa72996c4296f0d2638e431327f81b4de3bac241fb6ff01e769113f1f375b27
 
 
Sent from my iPhone using Tapatalk Pro

Amazing job and well beyond my capabilities! But I'm thinking forget the staff and concentrate on the roller table.
Try closing the hole with a suitable stake. Careful not to catch the jewel

Sent from my SM-G920F using Tapatalk

Link to comment
Share on other sites

Amazing job and well beyond my capabilities! But I'm thinking forget the staff and concentrate on the roller table.

Try closing the hole with a suitable stake. Careful not to catch the jewel

 

Sent from my SM-G920F using Tapatalk

 

Turns out you can close the hole in a balance table using the following:

e08da0802507253cbdfa3983e3813994.jpg

 

 

Sent from my iPhone using Tapatalk Pro

  • Like 1
Link to comment
Share on other sites

It worked. Now all i need to do is reduce the pivot size.066b34e7449d8121f48dd58f3efeb696.jpg&key=2e09e2bc75e7013778e9dac2d7ced237c7beea7b6e31b66d6b374ebbc4770f7e06fd1a18ae23b55de00406c58be6b238.jpg&key=3ecc20adea0d2bb606e715d3d0865230a4b21cdacec9e042e6abe25a664672b1ad7a86877432a4f0e940e05c14273413.jpg&key=88f2283ef9e039d019b8bbe99c10d8596351212d1233fb0de3e4646d9d94f784
Remember, i play guitar, thus the long nails:)
 
 
Sent from my iPhone using Tapatalk Pro
 
Excellent, is that a reverso staking set and you've used two stakes, the bottom being solid flat. Or is it a traditional stump ?

Sent from my SM-T585 using Tapatalk

Link to comment
Share on other sites

Excellent, is that a reverso staking set and you've used two stakes, the bottom being solid flat. Or is it a traditional stump ?

 

Sent from my SM-T585 using Tapatalk

 

You are correct. Flat Stake on bottom and round one on the top. Took a bit of pounding as well.

 

 

Sent from my iPhone using Tapatalk Pro

Link to comment
Share on other sites

You have achieved what is probably the hardest thing to make in in horology. You could have used lock tight; there are many types such as a thread lock tight, many people who make parts on lathes use it.

When using a punch you have to be very careful not to split the roller.

  • Like 1
Link to comment
Share on other sites

You have achieved what is probably the hardest thing to make in in horology. You could have used lock tight; there are many types such as a thread lock tight, many people who make parts on lathes use it.


When using a punch you have to be very careful not to split the roller.

Good advice. I'm going to cut a second balance staff this week. Finishing the pivots tonight, as my 4 new 0.2 and 0.4 round and flat carbide gravers are coming in tonight and a really need that round shape to finish the cone on the pivot.

Sent from my GT-N5110 using Tapatalk

  • Like 1
Link to comment
Share on other sites

I have the two sets of videos on using a lathe and I have the bible book on lathes "modern watchmakers lathe and how to use it" as well as practical watch repair and many other books. I have watched and read it all so my brain has the knowledge. Then I practiced for a week (4 hours or so) on brass stock. I then cot a stem using blue steel. And then I tackled the balance staff; taking my time and measuring and fitting as I built the part. I have learned about taking it slow as I over cut the roller table shaft a bit....good lesson. Next staff will be a lot better.

Sent from my GT-N5110 using Tapatalk

  • Like 1
Link to comment
Share on other sites

Are you doing anything different this time?


I am taking more time to taper the shaft so I don’t over cut any part (like the roller table last time). I also got four 0.2 and 0.4 square and round carbide gravers to finish the pivot better. I also started with 1.97 mm blue steel this time, so less cutting to the first diameter.

I am going to cut the staff with the stock attached and only leaving the Roller Table side pivot to complete. So i will complete one pivot before cutting off the part and reattaching to finish the roller side. I also purchased a triangle shaped Arkansas stone to finish the pivots, just prior to burnishing.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

What you did ~works~ in an <insert zenophobic ethnic slur here> worker kind of way. If you blow a measurement on a staff, only solution is to start again. What you did would work on a clock, but centricity on a watch balance is too critical. By tightening the roller table in a staking set you've mangled the center and I'd be surprised if you got that thing even well poised. Like I said though, it will ~work~ but you've just forfeited precision and introduced positional timing variability. 

Link to comment
Share on other sites

19 minutes ago, Tim said:

What you did ~works~ in an <insert zenophobic ethnic slur here> worker kind of way. If you blow a measurement on a staff, only solution is to start again. What you did would work on a clock, but centricity on a watch balance is too critical. By tightening the roller table in a staking set you've mangled the center and I'd be surprised if you got that thing even well poised. Like I said though, it will ~work~ but you've just forfeited precision and introduced positional timing variability. 

It will cause poor time keeping in a clock, so in fact it will not work.

Link to comment
Share on other sites

My experience with this is mainly pocket watches, in particular, "Waltham" The roller table is a friction fit and once removed for any reason can, on reassembly become loose, especially if removed several times. Reducing the bore size of the roller table is a method of rectification and would have Zero effect on the balance poise.
Also when fitting a new staff; even a factory manufactured one, on these old watches it is quite common to secure the balance wheel to the shaft in the way Jdrichard has done. Though a suitable hollow stump under the wheel arm is advisable, to avoid distortion to the balance wheel itself.

Sent from my SM-G920F using Tapatalk

  • Like 1
Link to comment
Share on other sites

My experience with this is mainly pocket watches, in particular, "Waltham" The roller table is a friction fit and once removed for any reason can, on reassembly become loose, especially if removed several times. Reducing the bore size of the roller table is a method of rectification and would have Zero effect on the balance poise.
Also when fitting a new staff; even a factory manufactured one, on these old watches it is quite common to secure the balance wheel to the shaft in the way Jdrichard has done. Though a suitable hollow stump under the wheel arm is advisable, to avoid distortion to the balance wheel itself.

Sent from my SM-G920F using Tapatalk



Digg is correct. This is a riveted staff so there is only one way to put it on. It is NOT a friction fit staff. I could have cut another staff, however, the text books do state that you can adjust the hole on the roller table the way i did it.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Does anyone knows what size case a need for a dial diameter 20.60mm?
    • Sounds like the story with my Rolex. Poor (expensive) job done by an official Rolex dealer with an "in-house" watchmaker, hence I learned watchrepair and did the servicing myself. Same story as I learned with the Omega 861, again poor job by an "in-house" watchmaker by an official Omega dealer. Once your watch goes through that back-door, you have no idea what is going to happening to it 🫣   Quite nice that they sent back the parts which had been replaced !
    • yes that's definitely not right at all. I have a picture one of my friends has a Omega coaxial there was having issues to lose asking me where he should send it. As that's a specialty watch I suggested the service center. When he got it back he sent me a picture so the replace the dial as you can see the hands the mainspring barrel and I think the price was really quite decent considering all the stuff they can replace. So I do know they do change the barrels but the other person I worked at the service center when I would ask questions and unfortunately I can't remember all the answers. I think a lot of the changing a parts is at the discretion of the watchmaker. Plus I don't know enough about the chronographs and whether that would be considered a vintage watch? I take some of the vintage watches may have been sent directly to Switzerland or another service center. Obviously with a watch like the one down below they probably have a infinite supply of parts is its relatively modern vintage stuff becomes more interesting even the watch companies don't have necessarily infinite supply of parts. But no matter what the watch shouldn't disintegrated six months that's definitely an issue.        
    • glad it worked out, those ESA movements are obsolete but new old stock is still out there, now that you know the make/model you could also do a cross reference to see if something more current would line up with the dial feet and hands...for future use if needed 👍
    • I wish they would have done so in this case. The whole story went like this: I sent my speedmaster to an omega service center about 10 years ago (at that point of time I haven't even started watchmaking). After the watch came back to me it had only about 6 months wristtime until january 2024 (not fair for this nice watch but the other pieces of my collection want wristtime too 🙂). So my conclusion is that the barrel was already faulty when it came back from service, can't imagine that amount of wear in 6 months wristtime. In january 2024 the performance on the wrist was quite bad, so I decided to have a look by myself. I have to admit that I didn't check the barrel close enough as I thought it must be ok, couldn't have issues after official omega service. That was a mistake, I will learn from that. Follow the golden rule: Nothing is certain except death and taxes.
×
×
  • Create New...