Jump to content

INCA BLOC HELL


Recommended Posts

AAAAARGGGGHHHHHH!!!!!!!!!!!!!!!!!!!!

Apologies for the disgruntled start but today has been one of those days. I am servicing my own Seiko diver with the Seiko 7S26 movement and after disassembly and cleaning I was reassembling and and all was going well until I took the Incabloc stones on of the barrel and train bridge. It took an hour and a half to get the first one back in after cleaning and lubing but the second one well lets just say that it is lost. It took me about 3 hours straight trying to get the butterfly spring to go into the slot but after about 15 times of it springing out and flicking the stone with it it pinged off one last time never to be seen again. I am frustrated as after watching Marks videos on his chanel he makes it seem so easy but that's because he has many years under his belt and this is my first time working with the butterfly type.

 

Earlier I had the Incablock spring on the balance of a CWC watch break when I was putting it back together so me and Incablocks this week are not friends.

 

Is here any tips or do's or don'ts anyone can share with this novice to make Incabloc work in the future easier?

 

Many thanks

 

Andy

 

Link to comment
Share on other sites

I know exactly how you feel and I have a very simple method for you. (it won't necessarily make things easier but you won't lose any parts)

I, too, struggle with incabloc parts so what I do is very simple. I actually put the movement on the movement holder into a transparent plastic zip lock bag along with the small components that have to be installed.

Then I simply fiddle around with the springs and the stones by using a thin tweezer (with care in mind so as not to damage anything or puncture the bag) until it works.

There are more complicated incablocs out there than the standard lyre shaped spring and this is what really helped.

One extra "tip". I would put the stone in it's slot, then the spring more or less into it's intended place, and to prevent it from jumping around I use the bag to block it from jumping by simply resting 2-3 of my fingers around the spot where I'm working. Just enough so that the bag will act like a wall that prevents the spring from jumping but not too much so that I would bend it.

I hope you understand what I'm saying... Good luck!

Edited by Chopin
  • Like 1
Link to comment
Share on other sites

@Andyworks, from your description of the stones on the barrel and train bridge it sounds as though you are refering to the Seiko Diafix settings for their cap jewels. These are a 3 pronged horse shoe shaped spring clip and they don't need to be removed. The trick with these is to free the middle tab from the retaining slot and then hinge the clip up with the two nd tabs still located. The jewel can then be removed, cleaned, and replaced without the clip ever leaving the plate.

I probably haven't described this very well but if you google Seiko Diafix, or have a look here;

https://adventuresinamateurwatchfettling.wordpress.com/2016/04/30/hidden-depths-a-seikomatic-r-from-1966/

you will see what I mean.

Incidentally Martin's blog is an excellent read, especially if you have an interest in vintage Seiko.

  • Like 1
Link to comment
Share on other sites

Seiko with Inca bloc springs? Never seen that? Seiko shok springs are the easiest ones to work on. Just put one end under the lip and twist. Diafix are tricky. But never seen that on a 7s26 . Is it the new or the old springs? 

The inca bloc  break from time to time . Use a sharp tweezer when open them. Put it back and close it when you clean the movement. Open it again with a oiler. Hardest to work on is the kif springs. Or the russian . 

  • Like 1
Link to comment
Share on other sites

Hi Marc, on the 7S26/36 the springs for the cap jewels are the new design. This is the rectangular-ish piece of metal similar to the newer balance shock spring but smaller. Google images '7s36 train bridge' for pics.

In terms of design.. the older 3-pronged design is more elegant but having broken some I have to say that the newer design is more robust.. if more difficult for those new to it. Personally I prefer the older design.

Anilv

 

Link to comment
Share on other sites

Fitting shock springs can take you to hell and back, However the more you practice the better you get at it.Tip 1. is to use cling film over the spring which really helps. Tip 2. is to have your workspace completely clear so when it goes into flight you have half a chance of finding it. Tip 3. is to de-magnitse the spring & tweezers/tools being used.

Link to comment
Share on other sites

For Inca I typically use a med (blue) oiler to nudge the arms out of the groove and also when replacing.

For some reason I have noticed Tissot watches are more prone to damaging the inca springs as most of the ones I've had to replace come from this manufacturer. Omega on the other hands seem to be fine.. surprising as both companies were linked closely in the 50s and 60s.

Anilv

Link to comment
Share on other sites

Thanks for all the useful tips and tricks. I will try these for sure. Sounds like I am not the only one that struggles with these. I notice as well there are many different systems and I can not find their names. I just generically refer to them as Incablocs although this is not correct. I am working on a CWC mechanical movement ETA 2750 and on the balance it has a broken spring that looks like this https://www.bing.com/images/search?view=detailV2&ccid=es6%2ft9NH&id=45A43BDCF8672559FE9B0BCADC38815172195B5F&thid=OIP.es6_t9NHOVRRNSes09R7TQEnEs&q=cwc+mechanical+watch&simid=607999746927035395&selectedIndex=106&ajaxhist=0

I need to get a replacement but it is not Inca so don't know the size or name to search for a replacement. Can anyone help please. Seems my shock spring nightmare is set to continue.

Andy

 

 

 

 

Link to comment
Share on other sites

5 minutes ago, Andyworks said:

Thanks for all the useful tips and tricks. I will try these for sure. Sounds like I am not the only one that struggles with these. I notice as well there are many different systems and I can not find their names. I just generically refer to them as Incablocs although this is not correct. I am working on a CWC mechanical movement ETA 2750 and on the balance it has a broken spring that looks like this https://www.bing.com/images/search?view=detailV2&ccid=es6%2ft9NH&id=45A43BDCF8672559FE9B0BCADC38815172195B5F&thid=OIP.es6_t9NHOVRRNSes09R7TQEnEs&q=cwc+mechanical+watch&simid=607999746927035395&selectedIndex=106&ajaxhist=0

I need to get a replacement but it is not Inca so don't know the size or name to search for a replacement. Can anyone help please. Seems my shock spring nightmare is set to continue.

Andy

 

 

 

 

 Been working at those a lot. They are a nightmare and i am afraid i am going to break one every time i open one.  But not sure what type they are? looks like a inca but has a different shape? 

Does it look like this? DSC01608.jpg.8c4f38f0533cb213b01769df6f844b07.jpg

Link to comment
Share on other sites

Hi Rogart63

 

Yes that is exactly how the spring looks. I ordered the ones for an ETA 2750 as listed on Cousins and parts pages and the ones that arrived were Inca block ones and they were far too large so ordered a smaller standard Inca style and have proved a nightmare to fit so assume the inca and the ones shown above are very different in dimensions and design etc? Do you know what they are called style wise and where I can order replacement springs and the best way to fit them?

 

Andy

Link to comment
Share on other sites

1 hour ago, Andyworks said:

Hi Rogart63

 

Yes that is exactly how the spring looks. I ordered the ones for an ETA 2750 as listed on Cousins and parts pages and the ones that arrived were Inca block ones and they were far too large so ordered a smaller standard Inca style and have proved a nightmare to fit so assume the inca and the ones shown above are very different in dimensions and design etc? Do you know what they are called style wise and where I can order replacement springs and the best way to fit them?

 

Andy

Never seen them in any other movement then the CWC ETA 2750 watches. 

Have a ETA 2750 somewhere here i think. Will take a look. If you can't solve it you can take a complete balance bridge from a Certina 25-... or ETA 2750 . Done that. but it's annoying not to now and it would help a lot. See if i can ask around on some forums. Like MWR maybe? 

Link to comment
Share on other sites

That 2750 i had used normal inca bloc springs of some sort. Did put a question up on MWR forum. As it is a military watch i am sure they now. or i will find out somewhere else. I did a shock spring thread on this forum . But not sure where it is. 

Link to comment
Share on other sites

@Andyworks i think i solved the mystery? It's a lubrifix 66 shock spring . They sit on a few other movement. like the ESA 9157 and ESA 9200 . Take a look at http://www.ranfft.de/uhr/index-e.html

Roland Ranfft help me in the right direction. Thanks Roland :) Not sure you are here on the forum . 

I can take a look as i have some old ETA 9157 and 58 tomorrow. Maybe they have that spring. 

 

Link to comment
Share on other sites

I will. Found a 9157 that has the same kind of springs. Don't want to remove the spring from the balance bridge. But got a complete unit from the mainplate. That i can send to you if you want. I bought a bunch of ETA 9200 from ebay that has the springs. So a few more is coming in. I think you need at least one more. They aren't the easiest to replace. 

Link to comment
Share on other sites

  • 1 year later...

I've found the best way to fit a true INCABLOC lyre spring is to hold the tips of the lyre (opposite from the hinge) between two pieces of scotch tape. 
then you can hold the scotch tape between your fingers while manipulating the hinge into the block with your finest tweezers.
an added advantage is that if it springs out, you still have hold of the tape and the spring doesn't shoot off anywhere.
it took me hours of pinging and searching with a magnet and then de-magnetizing and trying again and again before I came up with this method and it worked first time with no problem.
Of course the incabloc base block must be removed from the movement or pushed out enough to get the hinge end of the spring inserted.

Link to comment
Share on other sites

45 minutes ago, Pen said:

I've found the best way to fit a true INCABLOC lyre spring is to hold the tips of the lyre (opposite from the hinge) between two pieces of scotch tape. 
then you can hold the scotch tape 

Have you ever heard of Rodico? It can hold and pick up pretty much anything.

  • Like 1
Link to comment
Share on other sites

On ‎10‎/‎3‎/‎2017 at 1:42 PM, rogart63 said:

Seiko with Inca bloc springs? Never seen that? Seiko shok springs are the easiest ones to work on. Just put one end under the lip and twist. Diafix are tricky. But never seen that on a 7s26 . Is it the new or the old springs? 

The inca bloc  break from time to time . Use a sharp tweezer when open them. Put it back and close it when you clean the movement. Open it again with a oiler. Hardest to work on is the kif springs. Or the russian . 

     have you worked on a Wyler inca  bloc?

Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
×
×
  • Create New...