Jump to content

foreign brietling navitmer movement


Yorkie

Recommended Posts

hi, 

A friend dropped off his foreign Brietling, said had broken the stem.

appears to be a standard setup with subdials at 12:00/9:00/6:00

i have been trying to identify the movement, but i am struggling after the usual Cousins & internet search, in order to get a stem and crown etc.

I removed the dial to help with identification and in doing so broke the 12:00 hour recorder subdial spindle.

Any thoughts on swapping the movement, or general advice would be most helpful....

many thanks

IMG_1569.JPG

IMG_1570.JPG

IMG_1571.JPG

IMG_1632.JPG

IMG_1635.JPG

Link to comment
Share on other sites

16 minutes ago, Yorkie said:

A friend dropped off his foreign Brietling, said had broken the stem.

I don't get the point of using an unusual euphemism, as there is no censorship here. Call it for what it is, a fake.
An original stem may possibly work, but I don't really know.

Link to comment
Share on other sites

hi JDM , i am learning and a good point on the euphemsim thanks.

guess first i try some chinese 7750 stems, then try to find a 12:00 subdial recorder wheel and replace that.

if not, then i try to replace the movement, but I checked cousinsuk movements but could not find a similar 26mm x 6.25mm movement.

 

hi Chopin, will check and confirm anyways.

 

thanks

Link to comment
Share on other sites

1 hour ago, Yorkie said:

guess first i try some chinese 7750 stems, then try to find a 12:00 subdial recorder wheel and replace that.

if not, then i try to replace the movement, but I checked cousinsuk movements but could not find a similar 26mm x 6.25mm movement.

I stand corrected, not an A7750, but some other sort of contraption with month / moon / 24hr.
From Cousins it's an DG3836IB, although the same money would buy a lot more Chinese quality and honesty on AliExpress.

Edited by jdm
Link to comment
Share on other sites

Hello Yorkie,

Disregard the watch (or semantics) snobs and use whatever words you choose to describe the movement. Getting to your problem: Check O. frei as the have a large selection of chinese movements. I am sure Cousins UK does too.

It looks like it may be one of these:

59be7247c7bde_ScreenShot2017-09-17at8_59_22AM.thumb.png.5672d2711affc7671f93fd7e8ed8dae7.png

 

Link to comment
Share on other sites

Just now, noirrac1j said:

Disregard the watch (or semantics) snobs and use whatever words you choose to describe the movement. Getting to your problem: Check O. frei as the have a large selection of chinese movements. I am sure Cousins UK does too.

It looks like it may be one of these:

59be7247c7bde_ScreenShot2017-09-17at8_59_22AM.thumb.png.5672d2711affc7671f93fd7e8ed8dae7.png

 

No snobism here, just calling calling things their name. I'm sure that is something you appreciate too.

The mov.t in question is not a small seconds one; I've indicated model and availability above.

Link to comment
Share on other sites

Fake of course. The movement is based on the DG2813 which is based on the Myiota 8xxx something. 

Nice accurate movement if properly serviced and adjusted that can be found in most low-mid grade replica watches. 

Not a chronograph for sure :D

Edited by szbalogh
  • Like 1
Link to comment
Share on other sites

I'm glad you've got it sorted out. I am a collector and have high-end and low-end watches, and don't own any replica watches, but I defend anyone's decision to do so. Besides, you asked for repair help, not input on whether it's  real or not!

Looking forward to your future posts.

Regards,

J

Link to comment
Share on other sites

13 hours ago, noirrac1j said:

I'm glad you've got it sorted out. I am a collector and have high-end and low-end watches, and don't own any replica watches, but I defend anyone's decision to do so. Besides, you asked for repair help, not input on whether it's  real or not!

And help was given. In the end, you're still quibbling about nothing, when the OP has already extended his thanks to everybody. Time to move on, right?

  • Like 1
Link to comment
Share on other sites

3 hours ago, jdm said:

And help was given. In the end, you're still quibbling about nothing, when the OP has already extended his thanks to everybody. Time to move on, right?

Nobody is bringing this up except you @jdm. Yorkie already expressed his thanks to me , and you need to own your remark.  So what's you beef now?

J

 

Link to comment
Share on other sites

On 9/19/2017 at 5:15 PM, noirrac1j said:

Nobody is bringing this up except you @jdm. Yorkie already expressed his thanks to me , and you need to own your remark.  So what's you beef now?

That you started calling others snobist, and continued saying that judgment was given instead of help. And here I'm owning my remark again:

From Cousins it's an DG3836IB, although the same money would buy a lot more Chinese quality and honesty on AliExpress.

Now please, would you drop it and move on.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Well I put the spa on Gumtree (selling service) to try and sell it as it only needs a recirc pump to get it going. However, it weighs circa 250kg, so there's 4 fairly strong guys, and I would have to remove the sliding door in the room completely to be able to get it out, as well as clearing out a multitude of potted plants and the Alfresco outdoor setting to be able to get it out. Then move nearly everything in the back of the garage to be able to push it through to the front of the house. I would also need to hire furniture skates to be able to shift it around as carrying it is out of the question. Then someone would need a trailer to get it to their place as you won't get it on the back of a ute. So, the only answer is, out with the reciprocating saw and cut it all up into manageable pieces. Crying shame as it is in really good nick. I was only asking $1,500 and only got two bites, but it would only take something to go wrong with removing the sliding door etc that everything I make on the sale could go out the door on repairs etc. It would have been nice to be able to turn it into tools etc, but que sera sera. I don't know about the rest of the world, but there just seems to be very little interest from people wanting to buy things secondhand.  
    • I would like to see the movement. The watch is the movement. Anyone can print a name on a dial and sell it as "the maker".
    • Thanks for your answers! There seems to be a contradiction between these two answers, so perhaps I need to clarify. The flat and convex jewels look identical on the side facing away from the pivot shoulder. That is, there is an oil reservoir. I don't know if that changes anything but I thought it was safest to clarify since I didn't include a picture of the jewels from the opposite side.
    • unfortunately paying attention to details bumps up the cost. Which is why they shortchange on manufacturing steps if they can.
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.  When it comes to tools buy the best you can afford a good set of watch makers screwdrivers if you look after them will last you a life time. I recommend Dumont tweezers Number 3 and number 5 for fine work, you can build up from there. You will need different strength eye glasses. Some now like to work using a microscope. Pliers the box jointed ones are best they don't go out of line.     
×
×
  • Create New...