Jump to content

Howard Miller Triple Chime


ricardopalamino

Recommended Posts

Aloha All , 

I'm not really a collector of clocks or pocket watches , although I have a few of each I picked up in my searches down different avenues . 

I managed to pick up this Howard Miller Triple Chime Mantle clock at the swap meet for $65 with intentions to resell it on craigslist or ebay . I think the model is called ,"Bellingham" .

This particular clock has triple chimes that can be selected with a lever behind the dial glass and it can also be silenced with the same lever .  It has 8 hammers and what ever you call the things that the hammer strikes . What struck me is the beautiful tone of the chimes . The chimes that can be selected are called Whitt. , St. Michael's , and Westminster ,...I think . Please correct if I'm in error on these chime names .  Anyway , I am partial to the St . Michaels chime ,...very nice , melodic , and mellow .

And some Pics to share...

Thanks , 

Louis

 

 

Screen Shot 2017-09-04 at 2.22.39 PM.png

Screen Shot 2017-09-04 at 2.22.50 PM.png

Screen Shot 2017-09-04 at 2.23.06 PM.png

Screen Shot 2017-09-04 at 2.23.17 PM.png

Screen Shot 2017-09-04 at 2.23.31 PM.png

Screen Shot 2017-09-04 at 2.23.41 PM.png

Screen Shot 2017-09-04 at 2.23.51 PM.png

Screen Shot 2017-09-04 at 2.24.00 PM.png

Screen Shot 2017-09-04 at 2.24.12 PM.png

Edited by ricardopalamino
Link to comment
Share on other sites

Thats a nice clock.It looks like it has a newish case & dial. I would also say it is what is called a Napoleon hat style case and the movement has a floating balance which has the advantage of not needing to be exactly level for it to work efficiently.

Link to comment
Share on other sites

Thanks for all the great Info fellows .

Clockboy ,  I may be mistaken , but I don't think the clock is that old . In my little bit of research I think I found an approx . date of manufacture and I seem to remember I was surprised that it was older then I thought it might be . 

Oldhippy , you are , as always , a plethora of information .  I'm glad you chimed in .....Yuk Yuk..

Howzit vinn3 , ....what's a "tamborie" ?

Link to comment
Share on other sites

The movement is a Franz Hermle 1050-020 rebadged for Howard Miller it is as already stated very modern. Franz hermle movements are date coded they use to have up until 1988 a two digit number representing the year 85, 1985 86, 1986 and so on, they then changed to a date letter starting off with A, in 1988 B, 1989, C, 1990 and so on. Look just above the Howard Miller stamp and see if there is a date letter that should give you the year of manufacture.

Edited by wls1971
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Sounds great! And yes, I would use grease for the keyless as well although treating the parts with epilame would make the grease less likely to spread in the long run. Not critical but won’t hurt. My current strategy is to epilame treat all parts getting in contact with oil or grease.
    • Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.       I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • Hello and welcome from Leeds, England. 
    • Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
×
×
  • Create New...