Jump to content

Citizen 6031 Movement Question

PJA

By PJA
in Watch Repairs Help & Advice

 Share

Recommended Posts

PJA WRT Addict

PJA

Posted
Posted

Hello there. My wife has an old Citizen 6031 watch which probably hasn't been used for at least 10 years (was belong to her late father) and after changing battery and not getting any reaction I've taken it to a repair and the gentleman basically put a drop of some liquid on it which made it works for about 5 minutes and then stopped working again. My question is could it be that the oil dried after many years of not working or how to go about trying fixing it? I have ordered a new equivalent movement which I am waiting for, but for my practice I just wanted to try to fix it even though it doesn't pay. Thank you for your assistance.

Citizen_6031-G08644_YO.jpg

Link to comment
Share on other sites
Chopin Super WRT Addict

Chopin

Posted
Posted

Quartz movements can and certainly should be serviced just like mechanical ones. But we're usually talking about quartz movements that were made to be serviceable (so not the cheap chinese plastic ones...).

I would say that this one can be serviceable and you could certainly give it a try. I find them a lot more simple than most mechanicals.

Only wish they were larger in size as it's a fiddly job.

This type of movement could also require short circuiting it to start.

  • Like 1
Link to comment
Share on other sites
PJA WRT Addict

PJA

Posted
  • Author
Posted
53 minutes ago, Chopin said:

Quartz movements can and certainly should be serviced just like mechanical ones.

I would say that this one can be serviceable and you could certainly give it a try.

 

Thank you.

Link to comment
Share on other sites
PJA WRT Addict

PJA

Posted
  • Author
Posted
2 hours ago, Latvas said:

Have you tried line release cleaning

 

No, I haven't. I am just starting now with this hobby and not even know where to start, but can you give me a few words about how to go about it? I was trying to search it and can't find anything about it. Thank you.

  • Like 1
Link to comment
Share on other sites
Neileg WRT Addict

Neileg

Posted
Posted

Most quartz watch testers have this function. It creates a spinning magnetic field that drives the watch mechanism at speed. This can be enough to break loose old crusty oil or slight corrosion and get the watch running.
It's a bit quick and dirty as watch repairs go but can be very effective especially if the watch has been sitting unused.
Neil


Sent from my iPhone using Tapatalk

  • Like 2
Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted
7 hours ago, Latvas said:

go to ebay, and search for , quartz line release.


Sent from my iPad using Tapatalk

Line release is a novel way to release a gummed up quartz movement. However it does not offer a long term fix. I would relace the movement.

  • Like 1
Link to comment
Share on other sites
PJA WRT Addict

PJA

Posted
  • Author
Posted
12 hours ago, Latvas said:

I was searching for line release tools and correct me if I'm wrong, as I see it only the Horotec Turbo spins the dials while the others do only battery check like with multimeter without opening the back case?

Link to comment
Share on other sites
  • 6 months later...
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...