Jump to content

First time lumed dial..

DJW

By DJW
in Your Walkthroughs and Techniques

 Share

Recommended Posts

DJW Super WRT Addict

DJW

Posted
Posted (edited)

I'm very satisfied with how this dial turned out. I'm building and Elgin pocket watch conversion into wristwatch and wanted a vintage military dial look. 

I had recently purchased a lume kit but hadn't had the chance to use it yet. I design the dial with bold outlined numerals for the purpose of filling with lume. It really turned out better than I ever hoped!

The first dial I did turned out very acceptable, except that I had another issue with it and had to start over. I learned quite a bit just from doing that one dial.

Once I had the printing plate made I repainted the original Elgin dial to a flat white. I then Inked the plate and printed the new dial. Once everything was dry I then slowly added the lume using a 100 - 0 paintbrush which is about the size of a watch Oiler. I went around the dial 4 times adding a layer little by little. I'm very surprised just how much Lume this process adds. The markers have a nice three-dimensional heft to them...

IMG_20170812_213625.jpg

IMG_20170812_213129041_HDR.jpg

IMG_20170812_214600436_HDR.jpg

IMG_20170812_213512.jpg

Edited by DJW
  • Like 11
Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

I will try to put together a walk-through of the process of dial printing along with creating the plate itself. Honestly I spend more time on the computer designing the dial layout then it takes two create the actual plate or print the dial.:wacko:

 

IMG_20170813_165330.jpg

IMG_20170813_165420.jpg

IMG_20170813_194608.jpg

  • Like 5
  • Thanks 3
Link to comment
Share on other sites
  • 1 month later...
  • 5 months later...
  • 2 weeks later...
Deggsie WRT Addict

Deggsie

Posted
Posted
Yes!!! I've been wanting to that to make dials for the Chinese movements that seem to not have any unless you but some brand that uses the dial. I know they have number stickers but if I could design my own I would simply be in heaven!

Hi again DJW, if it makes life easier for you, do you have a suitable link to a website which explains the dial printing process please? As you might have noticed, the natives are restless and want to know more[emoji6]


Sent from my iPhone using Tapatalk
  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
20 minutes ago, Deggsie said:

Hi again DJW, if it makes life easier for you, do you have a suitable link to a website which explains the dial printing process please? As you might have noticed, the natives are restless and want to know moreemoji6.png

It's nothing secret, but beside the printing "machine" itself, the need to use a precisely engraved plate places the job largely outside the domain of the average hobbyist and even professional watchmaker  I think that if you can find someone that makes the plate on your design, or are willing to spend pretty good money on a CNC machine that does that, you could be game. I don't know if 3D printing would do a good enough plate. Fact is, at the present time dial making/reprinting specialists are rare.

 

Link to comment
Share on other sites
  • 3 months later...
rickhufnagel7 Member

rickhufnagel7

Posted
Posted

This is incredible! Awesome job! I have the same movement I've been trying to figure out how to do the dial forever. I've thought about the whole water slide decals, having vinyl made, trying to have someone hand paint it, nothing is ever as nice as the real deal like you have. I bow at you completing a project I've only begun to think about! It's beautiful.

Sent from my Moto E (4) using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...