Jump to content

My newest work space...I have to quit moving!


DJW

Recommended Posts

Since I joined this forum I've moved half a dozen times. Each time I have to fit what I have to work on watches and whatever little space that's available. This time I'm in the smallest place yet (460sqft.) but have the perfect little niche in the corner for all of my watch making tools, supplies, books, Etc. All that and a South facing window B) plus, I can keep an eye on my beloved car that sits right in front of that window:biggrin:

IMG_20170609_175554024_HDR.jpg

IMG_20170609_175522593_HDR.jpg

  • Like 9
Link to comment
Share on other sites

 

A nice light room even if its small. The L & R varimatic is the best cleaning machine I ever had.How do you manage to work on your lathe tucked in that corner with all the other stuff around.

It's tight, but not terrible. It may not look it, but there is just enough room to sit comfortably at the lathe..

Link to comment
Share on other sites

 

By the way, what's the tool in the back left corner of the bench?

I think you're asking about my plastic Crystal lift/compressor? I don't use it that often, but it's nice to have if I have a very tight plastic Crystal to install..

Link to comment
Share on other sites

 

 I'm very excited to pick up an L&R on Monday and graduate from my jewelry cleaner

 

The only issue I've had with this machine is the seals drying out. There is a place online where I could buy new ones, but as long as I leave it in the down position with no load on the hydraulic system I don't have a problem with fluid leaking out of the reservoir. 

After the machine completes the drying cycle the hydraulic ram lifts the head up about three or four inches so that you can remove the basket with the watch components. This is the final position that the watch cleaning machine ends it cycle. The problem with this position is that the hydraulic pressure keeps it at this elevated position. There is a spring inside the shaft that constantly pulls the head back down towards the machine itself. So therefore there is a constant positive pressure on the hydraulic system. If you have leaky seals like I do in my machine, it will slowly bleed off fluid out of the seals until the head drops all the way down back into the drying position. Because I turn it off at near the end of the drying position the hydraulic system is not under load and I don't lose any fluid. I would recommend keeping your machine in this position as well as there is no stress on the hydraulic system or seals...

When you want to clean a new watch, all you have to do is turn the machine on and the head will lift up to the final position at that point. Then you can attach your basket and press start and off you go. You just have to remember to turn off the machine during the drying cycle so it stays in that position. If you forget and it right raises up to the final point I just cycle all the way through back around to the drying cycle and then shut it off then.. obviously with the basket removed so that my freshly cleaned and dried watch Parts don't get a quick bath!:wacko:

 

Link to comment
Share on other sites

 

how is the weather in Seattle?

It's been beautiful lately! Hot as hell on Sunday..93 degrees:blink:...After the winter we had, I'll take it. We broke a record for rain- 45 inches from October 2016-April 2017...Geez!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Looks that way, if it had any amount of significant jewel count it would say so on the dial.    Looks that way, if it had any amount of significant jewel count it would say so on the dial.  Same answer as Mike regarding the dial, its often just a slapped on name of a retailer but i thought you were way above this understanding Pete ?
    • Light naptha is what you need to be looking for. The carbon to hydrogen ratio is high with heavy naptha, it doesn't evaporate as well as light naptha and is prone to leaving more residue. Try tom's suggestion of the mirror test.
    • Its a big item Michael and a lot that could go wrong with the process of getting it to its new location. I once helped install one of these units into a conservatory that i had built. It was big and bloody heavy and took six of us to get it in safely. If you have sliding doors and you need to remove the whole frame then that may or may not go well. But i would advise getting a professional in if you have little knowledge on the installation of them. The glazing of the doors could well be 6mm laminated glass which again will be heavy very heavy if the glazing units are big. The glass would also need to be set up and packed correctly to open the doors properly more so if they are unframed and the sliders are upvc. Seems a shame but if no one is biting and that may be due to having no warranty i guess the only takers might be someone that installs them for a living and knows how to repair. If its fibreglass just be careful, i sometimes have to cut fibreglass baths out and they are nasty to work with . Thick gloves are definitely recommended,  not fun picking out fibreglass spells two days later that have started to go septic. Good luck with it all matey.
    • I don’t know anything about this product, however assuming you have it if you put a drop on a mirror or piece of glass lying flat on a table and leave it to evaporate if it leaves any sort of residue it is not really suitable for watch part cleaning.   Tom
    • Well I put the spa on Gumtree (selling service) to try and sell it as it only needs a recirc pump to get it going. However, it weighs circa 250kg, so there's 4 fairly strong guys, and I would have to remove the sliding door in the room completely to be able to get it out, as well as clearing out a multitude of potted plants and the Alfresco outdoor setting to be able to get it out. Then move nearly everything in the back of the garage to be able to push it through to the front of the house. I would also need to hire furniture skates to be able to shift it around as carrying it is out of the question. Then someone would need a trailer to get it to their place as you won't get it on the back of a ute. So, the only answer is, out with the reciprocating saw and cut it all up into manageable pieces. Crying shame as it is in really good nick. I was only asking $1,500 and only got two bites, but it would only take something to go wrong with removing the sliding door etc that everything I make on the sale could go out the door on repairs etc. It would have been nice to be able to turn it into tools etc, but que sera sera. I don't know about the rest of the world, but there just seems to be very little interest from people wanting to buy things secondhand.  
×
×
  • Create New...