Jump to content

Favre-Leuba


Johnnie

Recommended Posts

Hello one and all, the postman arrived yesterday bringing me this watch! Being pretty new here and of very little experience I thought the I would run it past you all for advice and opinions. It is quiet a small watch measuring a tad under 30mm without the crown. Looking at the movement it says "twin power" and when you try to wind it, it feels locked up or as I used to say before joining this forum "overwound" any advice gratefully received. Johnnie

IMG_20170618_154300.jpg

IMG_20170618_154330.jpg

IMG_20170618_154340.jpg

IMG_20170618_154356.jpg

Link to comment
Share on other sites

Sorry to say but i think that dial is repainted. Movement is a genuine Favre-Leuba though . A so called Twinpower. http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&&2uswk&Favre-Leuba_259

A really nice movement . It would probably need a service. It has double mainsprings so probably not the easiest movement to start with? 

Edited by rogart63
  • Like 1
Link to comment
Share on other sites

Nice watch.  A lot of Favre Leubas show up with repainted dials for some reason.  I think they were popular in India and haven't aged well in the climate.  I like the movement but I wouldn't want to pay for two mainsprings in one service- funny but that's the first thing that came to my mind when I saw the double barrels!

  • Like 1
Link to comment
Share on other sites

Hi Ry. Two mainsprings well that's a one in two chance of making a pigs ear of it LOL. I will try and read up on this movement before I touch it. Will Google it and see if anything useful comes up about it. Best wishes Johnnie

  • Like 2
Link to comment
Share on other sites

Hi Johnnie, I love this movement.. when you get it working you'll see that it winds super smooth and it's pretty accurate too!

Does the balance swing freely? Could be it had a 'jolt' and the impulse pin came out of the fork. If this was the case the balance would stop on one side like it hit a brick wall.

Its a simple enough movement. I usually keep the barrels separate. I seem to remember one being slightly different but its been a while since I worked on one. Anyway, even if they're identical its good practice to re-install them where they came from as they would have worn together.

One peculiarity on this movement is how FL fixed the end of the hairspring, it is screwed to the underside of the balance bridge. To adjust the beat you have to remove the balance + bridge, loosen the holding screw (enough so there's still a bit of friction), install balance + bridge, set the beat-rate by moving the visible end of the hairspring end (you can just see a metal piece with a hole below the bridge above the balance). Remove the balance+bridge, tighten the screw fixing the hairspring end. reassemble. The beauty of this arrangement is that it will not move if the watch is dropped.

Anilv

  • Like 3
Link to comment
Share on other sites

Hi Anilv, thanks for replying and the information (much needed) as I could write all my watch repair knowledge on the back of a postal stamp. The balance wheel moves freely when I use a puffer on it, so I am hoping that there isn't too much wrong with it? When your knowledge is as limited as mine is you can't always spot what is wrong unless it is obvious, but hopefully with time and more reading and practice I will become more competent. As I disassemble the movement I will take a photo every time I remove a part that way I will at least I will know where all the pieces go! Thanks again Anilv best wishes. Johnnie

Link to comment
Share on other sites

Hi Rogart63, Sorry for late reply, I did reply but forgot to click submit reply (had a senior moment) I seem to be getting them more often of late!!!! Yes I think you are right about the dial and it not being an ideal movement for a beginner.. I didn't know what movement it had until I opened it up. Thanks for the link, very useful. Will read up as much as possible before I touch it. Best wishes. Johnnie

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
×
×
  • Create New...