Jump to content

Favre-Leuba

Johnnie

By Johnnie
in Your Watch Collection

 Share

Recommended Posts

Johnnie Super WRT Addict

Johnnie

Posted
Posted

Hello one and all, the postman arrived yesterday bringing me this watch! Being pretty new here and of very little experience I thought the I would run it past you all for advice and opinions. It is quiet a small watch measuring a tad under 30mm without the crown. Looking at the movement it says "twin power" and when you try to wind it, it feels locked up or as I used to say before joining this forum "overwound" any advice gratefully received. Johnnie

IMG_20170618_154300.jpg

IMG_20170618_154330.jpg

IMG_20170618_154340.jpg

IMG_20170618_154356.jpg

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

Sorry to say but i think that dial is repainted. Movement is a genuine Favre-Leuba though . A so called Twinpower. http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&&2uswk&Favre-Leuba_259

A really nice movement . It would probably need a service. It has double mainsprings so probably not the easiest movement to start with? 

Edited by rogart63
  • Like 1
Link to comment
Share on other sites
RyMoeller Super WRT Addict

RyMoeller

Posted
Posted

Nice watch.  A lot of Favre Leubas show up with repainted dials for some reason.  I think they were popular in India and haven't aged well in the climate.  I like the movement but I wouldn't want to pay for two mainsprings in one service- funny but that's the first thing that came to my mind when I saw the double barrels!

  • Like 1
Link to comment
Share on other sites
Johnnie Super WRT Addict

Johnnie

Posted
  • Author
Posted

Hi Ry. Two mainsprings well that's a one in two chance of making a pigs ear of it LOL. I will try and read up on this movement before I touch it. Will Google it and see if anything useful comes up about it. Best wishes Johnnie

  • Like 2
Link to comment
Share on other sites
anilv Distinguished Member

anilv

Posted
Posted

Hi Johnnie, I love this movement.. when you get it working you'll see that it winds super smooth and it's pretty accurate too!

Does the balance swing freely? Could be it had a 'jolt' and the impulse pin came out of the fork. If this was the case the balance would stop on one side like it hit a brick wall.

Its a simple enough movement. I usually keep the barrels separate. I seem to remember one being slightly different but its been a while since I worked on one. Anyway, even if they're identical its good practice to re-install them where they came from as they would have worn together.

One peculiarity on this movement is how FL fixed the end of the hairspring, it is screwed to the underside of the balance bridge. To adjust the beat you have to remove the balance + bridge, loosen the holding screw (enough so there's still a bit of friction), install balance + bridge, set the beat-rate by moving the visible end of the hairspring end (you can just see a metal piece with a hole below the bridge above the balance). Remove the balance+bridge, tighten the screw fixing the hairspring end. reassemble. The beauty of this arrangement is that it will not move if the watch is dropped.

Anilv

  • Like 3
Link to comment
Share on other sites
Johnnie Super WRT Addict

Johnnie

Posted
  • Author
Posted

Hi Anilv, thanks for replying and the information (much needed) as I could write all my watch repair knowledge on the back of a postal stamp. The balance wheel moves freely when I use a puffer on it, so I am hoping that there isn't too much wrong with it? When your knowledge is as limited as mine is you can't always spot what is wrong unless it is obvious, but hopefully with time and more reading and practice I will become more competent. As I disassemble the movement I will take a photo every time I remove a part that way I will at least I will know where all the pieces go! Thanks again Anilv best wishes. Johnnie

Link to comment
Share on other sites
Johnnie Super WRT Addict

Johnnie

Posted
  • Author
Posted

Hi Rogart63, Sorry for late reply, I did reply but forgot to click submit reply (had a senior moment) I seem to be getting them more often of late!!!! Yes I think you are right about the dial and it not being an ideal movement for a beginner.. I didn't know what movement it had until I opened it up. Thanks for the link, very useful. Will read up as much as possible before I touch it. Best wishes. Johnnie

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Modular Movement Holder.pdf  
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Good job, that band matches the watch perfectly.
×
×
  • Create New...