Jump to content

1975 Timex Dynabeat - Basic Restore


Recommended Posts

Here we have a 1975 Dynabeat that cones from the Electric series Timex produced.   I'll start with the basic case tear down and preparation of cleaning.

Remove bezel ring, crown\stem, and crystal.   Next pull hands and remove dial.  Notice that these dials have tabs so care must be take not to over bend them.

For this I used a modified 45 degree Xacto blade which I'v added a notch to on the tip.  Place the edge of the blade at angle to tab and back the tab with you finger.

Lift slowly and move to next tab.  Notice that one tab is very close to the balance wheel.  This is where I use the notched tip.  Continue to remove the components under the dial.  Be careful with the date wheel detent spring as it very thin and bends easily.  

Now comes the step that many will find interesting or get a laugh over.  But, I tell you it works more times than not.  The idea behind this is to clean oxidation off the contact wire that bushes against the staff.  It also helps remove dried oil and other debris out of the movement.  I use a very high tech tool next to blow air to help dry the cleaner up.  "Okay so its just a cheap balloon pump". 

Next another tool I made up that is most helpful.  After dotting any pivots both top and bottom, I dab some oil to the train gears just next to the battery compartment.  Refit the stem, press down on a fresh battery and give the balance a flick.  Sometimes it takes a few but this one went off with just one.  clean and buff the outer parts, freshen up the hands, put it all back together.

There are some steps I left out and will add in future posting.

So what was the first thing that failed?  If you said the sweep fell off you would be right.  Why it fell off is because I forgot to tamp down the hole to be sure it fit tight again.

its has since been corrected and the watch is humming nicely.

Thanks for looking.

 

DSC05295.JPG

DSC05296.JPG

DSC05297.JPG

DSC05298.JPG

DSC05299.JPG

DSC05300.JPG

DSC05301.JPG

DSC05302.JPG

DSC05303.JPG

DSC05304.JPG

DSC05305.JPG

DSC05306.JPG

DSC05307.JPG

DSC05308.JPG

DSC05309.JPG

DSC05313.JPG

DSC05314.JPG

Edited by JerseyMo
spelling correction
  • Like 4
Link to comment
Share on other sites

 

isopropyl  alcohol  will do the same job,  without "spray mist'.  but,  good job!

very true, back when I did electronic video game board repairs it was very common to use alcohol as a cleaning agent.

on the other hand we discouraged to use of spray cleaners on the old electo-mechnical pinball machines because the residue

of conductive particles could drip between contact blades and relays.  Pulling apart a stack of relays was not fun.

Link to comment
Share on other sites

When the cleaning does not work is a good indication of component failure or other such malfunction.  This would require a more detailed inspection.  Such is beyond the scope of this posting.

However, back in the day, Timex made NOS and\or factory reconditioned movements available to service centers. They did also have the individual parts such as new balance coils, contact wires etc. available to service centers.  I have acquirement many of these and have a nice supply of parts on hand.

I have also networked with other "Timexicans" who enjoy working on the Electrics and often ask for their support and in turn I provide similar favor for repairs to the day\dates which can be as equal a challenge at times.

  • Like 1
Link to comment
Share on other sites

  • 3 years later...
On 6/10/2017 at 9:03 PM, JerseyMo said:

Here we have a 1975 Dynabeat that cones from the Electric series Timex produced.   I'll start with the basic case tear down and preparation of cleaning.

Remove bezel ring, crown\stem, and crystal.   Next pull hands and remove dial.  Notice that these dials have tabs so care must be take not to over bend them.

For this I used a modified 45 degree Xacto blade which I'v added a notch to on the tip.  Place the edge of the blade at angle to tab and back the tab with you finger.

Lift slowly and move to next tab.  Notice that one tab is very close to the balance wheel.  This is where I use the notched tip.  Continue to remove the components under the dial.  Be careful with the date wheel detent spring as it very thin and bends easily.  

Now comes the step that many will find interesting or get a laugh over.  But, I tell you it works more times than not.  The idea behind this is to clean oxidation off the contact wire that bushes against the staff.  It also helps remove dried oil and other debris out of the movement.  I use a very high tech tool next to blow air to help dry the cleaner up.  "Okay so its just a cheap balloon pump". 

Next another tool I made up that is most helpful.  After dotting any pivots both top and bottom, I dab some oil to the train gears just next to the battery compartment.  Refit the stem, press down on a fresh battery and give the balance a flick.  Sometimes it takes a few but this one went off with just one.  clean and buff the outer parts, freshen up the hands, put it all back together.

There are some steps I left out and will add in future posting.

So what was the first thing that failed?  If you said the sweep fell off you would be right.  Why it fell off is because I forgot to tamp down the hole to be sure it fit tight again.

its has since been corrected and the watch is humming nicely.

Thanks for looking.

 

DSC05295.JPG

DSC05296.JPG

DSC05297.JPG

DSC05298.JPG

DSC05299.JPG

DSC05300.JPG

DSC05301.JPG

DSC05302.JPG

DSC05303.JPG

DSC05304.JPG

DSC05305.JPG

DSC05306.JPG

DSC05307.JPG

DSC05308.JPG

DSC05309.JPG

DSC05313.JPG

DSC05314.JPG

Very helpful breakdown.  I just got a Dynabeat Time Zone.  It didn't have a battery when I bought it, so no corrosion.  Put in a new 357, but no action.  I know these sometimes need a little whack to get going, but nothing resonable has worked.  Any ogher suggestions before I break it down???  Thx!

Link to comment
Share on other sites

Very helpful breakdown!  I just got a Dynabeat Time Zone.  It didn't have a battery when I bought it, so no corrosion.  Put in a new 357, but no action.  I know these sometimes need a little whack to get going, but nothing resonable has worked.  It looks clean, no obvious issues on inspection. Certainly no rust.  Any other suggestions before I break it down???  Thx!

Link to comment
Share on other sites

1 minute ago, maxbernat said:

Put in a new 357, but no action.  I know these sometimes need a little whack to get going, but nothing resonable has worked.  Any other suggestions before I break it down??? 

If a shot with a demagnetizer or line release box doesn't start a quartz watch the module is toast.

  • Like 1
Link to comment
Share on other sites

I would connect a multimeter in ohmmeter mode to the +ve and -ve terminals then give the balance a good swing with a wood stick. If there is any reading at all, then there is hope. 

Spray contact cleaner on the contact wire and keep swinging the balance back and forth for awhile to breakdown any oxidation on the contacts. Then keep your fingers crossed, put in the battery and start it up again. 

This has worked for me so far except for one with a contact wire that seems to have lost its spring temper. It's all limp and gets bent very easily. I have no idea what happened to that.

Goodluck! :thumbsu:

  • Like 1
Link to comment
Share on other sites

4 hours ago, HectorLooi said:

I would connect a multimeter in ohmmeter mode to the +ve and -ve terminals then give the balance a good swing with a wood stick. 

I realize now  that is an electric movement, sorry I don't know anything about these, pls ignore my posting above.

  • Like 1
Link to comment
Share on other sites

  • 1 year later...
On 6/10/2017 at 9:03 PM, JerseyMo said:

Here we have a 1975 Dynabeat that cones from the Electric series Timex produced.   I'll start with the basic case tear down and preparation of cleaning.

Remove bezel ring, crown\stem, and crystal.   Next pull hands and remove dial.  Notice that these dials have tabs so care must be take not to over bend them.

For this I used a modified 45 degree Xacto blade which I'v added a notch to on the tip.  Place the edge of the blade at angle to tab and back the tab with you finger.

Lift slowly and move to next tab.  Notice that one tab is very close to the balance wheel.  This is where I use the notched tip.  Continue to remove the components under the dial.  Be careful with the date wheel detent spring as it very thin and bends easily.  

Now comes the step that many will find interesting or get a laugh over.  But, I tell you it works more times than not.  The idea behind this is to clean oxidation off the contact wire that bushes against the staff.  It also helps remove dried oil and other debris out of the movement.  I use a very high tech tool next to blow air to help dry the cleaner up.  "Okay so its just a cheap balloon pump". 

Next another tool I made up that is most helpful.  After dotting any pivots both top and bottom, I dab some oil to the train gears just next to the battery compartment.  Refit the stem, press down on a fresh battery and give the balance a flick.  Sometimes it takes a few but this one went off with just one.  clean and buff the outer parts, freshen up the hands, put it all back together.

There are some steps I left out and will add in future posting.

So what was the first thing that failed?  If you said the sweep fell off you would be right.  Why it fell off is because I forgot to tamp down the hole to be sure it fit tight again.

its has since been corrected and the watch is humming nicely.

Thanks for looking.

 

DSC05295.JPG

DSC05296.JPG

DSC05297.JPG

DSC05298.JPG

DSC05299.JPG

DSC05300.JPG

DSC05301.JPG

DSC05302.JPG

DSC05303.JPG

DSC05304.JPG

DSC05305.JPG

DSC05306.JPG

DSC05307.JPG

DSC05308.JPG

DSC05309.JPG

DSC05313.JPG

DSC05314.JPG

Thanks for your walk through!  I ordered a can of the contact cleaner which you show in your pictures.  I also have Watch Tech which I use for quartz watches.  Do you think it would work too?  Also, Timex recommends removing the balance and soaking it in modern watch cleaning solution which, won't damage the insulation on the coil.  Any idea what kinds of solutions you think might be safe?  Thanks!

Link to comment
Share on other sites

On 7/17/2020 at 9:23 AM, maxbernat said:

Very helpful breakdown!  I just got a Dynabeat Time Zone.  It didn't have a battery when I bought it, so no corrosion.  Put in a new 357, but no action.  I know these sometimes need a little whack to get going, but nothing resonable has worked.  It looks clean, no obvious issues on inspection. Certainly no rust.  Any other suggestions before I break it down???  Thx!

I have two Timex Time Zones.  One is missing the red, second zone, hour hand (just in case anyone has a spare) and both are gold toned.  I just had one on yesterday.  They are very smart looking watches.

Cheers

Shane

Link to comment
Share on other sites

On 1/14/2022 at 10:41 AM, DouglasSkinner said:

Thanks for your walk through!  I ordered a can of the contact cleaner which you show in your pictures.  I also have Watch Tech which I use for quartz watches.  Do you think it would work too?  Also, Timex recommends removing the balance and soaking it in modern watch cleaning solution which, won't damage the insulation on the coil.  Any idea what kinds of solutions you think might be safe?  Thanks!

Timex would have recommended standard watch cleaner solution.  The one part to be careful of is the balance coil which is coated with some type of lacquer\varnish or similar.  I have used alcohol was well as lighter fluid.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • @Murks the problem you have mate is most watch cases out there to buy are for Seiko NH3X, ETA 2824 and maybe Myota 8XXX movements, oh also the big ETA 6978/9 movements which the dials start around 28.5mm. You might find one on a Google search but I suspect your main chance will be buying cheap quartz ladies watches and hopefully find one of the right size and condition that is acceptable. 😞   Tom
    • The anchor pin should be perpendicular when the anchor is sat on a flat surface and if you post a close up picture of the backplate I will be able to tell you the correct torsion spring , running fast or slow is usually wrong Torsion spring. Here is a video from my YouTube channel showing how I set the beat  
    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be. You've signed up to another forum !!! Why you defector , you snake in the grass, you infidel consider yourself shunned.... you.......you........you CAD  😅😅😅😅😅😅🤪
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
×
×
  • Create New...