Jump to content

Summer project.

maclerche
 Share

Recommended Posts

maclerche WRT Addict

maclerche

Posted
Posted

I love mechanical things, not least the watches, clocks and other mechanical hardware. To be able to repair watches have been a wish in a really long time. Unfortunately I have not had a real place to practice and must recognize that doing it in the kitchen just cannot be reconciled with the family.

That is why I am now going to remodel our 70 's garage into a workshop and hobby room for joy for me and the rest of the family. It is anyway too small for a modern car.

The garage is at about 6.8 x 3 m. and there for approx. 20 square meters. The redevelopment will be extensive as i have to make heating and floor heating window and a small kitchenette. I am now almost finished clearing out the garage so that the work can begin. I will put up some pictures every now and then as the project progresses!

  • Like 3
Link to comment
Share on other sites
maclerche WRT Addict

maclerche

Posted
  • Author
Posted
 

try to get a window facing the sun rise.  have fun.  vinn

Unfortunately it is not possible right now. In the first place, I get a window to the West, later perhaps a narrow one facing north! Over time maybe a towards the East!

Link to comment
Share on other sites
  • 2 weeks later...
szbalogh Super WRT Addict

szbalogh

Posted
Posted

No reports from me for a long time but next week my family is leaving for a week and i will be back in business. Lots of plans including finishing a 1972 München pin lever watch (new baalnce turned), servicing some watches (Vostok Komandirskie, Ricoh auto, HMT maybe...), some enameling experiments, making some tools (faceplate for mainplate and case turning) and.... designing my own brand :)

  • Like 1
Link to comment
Share on other sites
maclerche WRT Addict

maclerche

Posted
  • Author
Posted

At the weekend i continued to work in the workshop. The load-bearing beams hase been attacked by boring beetles. If they are still active or not is hard to see, so I chose to smear with a means to be sure they are not coming back. 7.5 liters "PROTOX INSEKT" has come on with a brush. I have also created wind screen between the beams so that it does not blow into the insulation when it comes up. Today i started on the electrical installations in the ceiling, among other outlets for powering LED panels!

 

garage2.jpg

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rossjackson01
      Intro

      By rossjackson01 · Posted

      Welcome my friend. 
    • rossjackson01
      Help please.

      By rossjackson01 · Posted

      Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
×
×
  • Create New...