Jump to content

Seiko 7T32-6L20 Macchina Sportiva

systeman

By systeman
in Your Watch Collection

 Share

Recommended Posts

systeman WRT Addict

systeman

Posted
Posted

I've been looking for one of these for a very long time. I've just got my hands on a Seiko Macchina Sportiva from the 1990's, but this one is quite rare. It's the 7T32-6L20 Black ION with its original black rubber strap.

I've given it a full service but need to realign the date ring, that's not a problem. But what is a problem is the case back.

There's video I've made to show it off a bit.

The back on these was a silicone based black finish and this had deteriorated over time. Again, not too much of a problem, I'll completely strip back the back plate to bare metal and reapply a new decal to original spec.

59353a7e61fdc_Seiko7t32-6L20-1.thumb.jpg.22fd80f3820a8f1454a82a5cf77e1dbb.jpg

 

59353a8c49787_Seiko7t32-6L20-2.jpg.da23a5e8bb1d4d0ed4c447693ebb0ca3.jpg

 

59353a97a5fc4_Seiko7t32-6L20-3.jpg.07cb572afddcb08d6907edc1984ccc25.jpg

  • Like 4
Link to comment
Share on other sites
  • 2 months later...
systeman WRT Addict

systeman

Posted
  • Author
Posted
23 hours ago, StuartBaker104 said:

How did you do that? It looks great!

I took a photograph of a few Macchina Sportiva case backs and took measurements of the text, the logo panel and diameter of the text relative to the panel and case back.

I then edited and recreated the Logo panel in Gimp.

I recreated the circular text using the same font as a layer.

Then I created a black background layer the same overall size of the case back.

The artwork was the laser printed onto a transfer film ready for transferring to the case back.

Obviously, printers do not print white text. Therefore, I used an acid etch primer on the case back before painting it with an off white background for the text.

The transfer was then applied and baked on. A few coats of matte lacquer was then applied to seal and finish it off.

This is not one for the faint hearted, it needs a lot of patience.

  • Like 3
Link to comment
Share on other sites
PJA WRT Addict

PJA

Posted
Posted
13 hours ago, systeman said:

I took a photograph of a few Macchina Sportiva case backs and took measurements of the text, the logo panel and diameter of the text relative to the panel and case back.

I then edited and recreated the Logo panel in Gimp.

I recreated the circular text using the same font as a layer.

Then I created a black background layer the same overall size of the case back.

The artwork was the laser printed onto a transfer film ready for transferring to the case back.

Obviously, printers do not print white text. Therefore, I used an acid etch primer on the case back before painting it with an off white background for the text.

The transfer was then applied and baked on. A few coats of matte lacquer was then applied to seal and finish it off.

This is not one for the faint hearted, it needs a lot of patience.

Great job and very creative!

Link to comment
Share on other sites
  • 2 weeks later...
systeman WRT Addict

systeman

Posted
  • Author
Posted

I've now uploaded a video of the finished watch:

It was great fun getting involved with refurbishing the case back. After assembling and testing the functions, I did notice an improvement in the volume of the buzzer. This was probably because of baking the decal. The process must have improved the conductivity of the old adhesive.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Down the rabbit hole!

      By RichardHarris123 · Posted

      Well done, let us know how you get on with the citizen. 
    • tomh207
      Without Our Forum

      By tomh207 · Posted

      @Neverenoughwatches Rich, I can only agree with you wholeheartedly. I spend a lot of time here learning all sorts and trying to make any little contribution to help others I can. Nothing can last forever and I wish I could do more to contribute to the forum financially and any other support I could.   Tom
    • oldhippy
      Without Our Forum

      By oldhippy · Posted

      This forum is a big part of my life. When I retired from horology many years ago due to poor health I missed what I had trained for. On here I can still do my bit in helping and advising others and have a little fun as well.  
    • RichardHarris123
      Without Our Forum

      By RichardHarris123 · Posted

      First thing this morning, make coffee, second, check the forum.  I would really miss the forum, not on any social media, not interested in telling the world what I had for breakfast!!! I do consider most of the regulars friends and would wonder what had happened if they stopped posting. 
    • fnick
      Down the rabbit hole!

      By fnick · Posted

      Hi all Thought I'd show my small and trying to keep under control watch collection! Apart from the Enicar all were under £12! At least if I destroy them in the process then I won't be too worse off. A few pics to start off with First of all my first attempt. A Thuya pocket watch. It was only running face down and would stop when vertical. So now it still works face down and only slows down when vertical so at least an improvement! 😄  I only have a generic watch oil at the mo so that won't help but I'm hoping to get some more appropriate oils in a couple of months for my birthday. I did have to get a crystal for it since it didn't come with one. It didn't look as though it would friction fit (and I don't have a crystal press in any case) so I glued it to the case with PVA. So far so good. Next up above are a sekonda and citizen automatic. Both non runners. Both with broken balance wheels amongst other things. I'm hopeful the citizen will start when I get the new one I ordered but the sekonda is being kept for spares and trial of new techniques. And finally the Enicar and the timemaster. Both running when I got them. I wanted to get running watches so that at least I stood a fighting chance of still having a running watch after the service! It was all going well on the Enicar until I dropped the balance wheel during reassembly...😔. Unfortunately they are quite expensive to get so for now I'll won't do anything with it but I would like to fix it at one point. The timemaster is still running (yeah!) but I managed to break a dial foot during the deassembly. First repair attempt failed so now I am looking at soldering it back on... So there we go. My initial foray into this great hobby. Thanks for sticking with this tale so far.  I'm hoping that once the balance wheel arrives for the citizen I will be able to say I bought a non runner and fixed it! So fingers crossed. Thanks for looking, Nick
×
×
  • Create New...